Husqvarna 353 EPA III TrioBrake, 345e EPA III manual Cutting equipment designed to reduce kickback

Page 12

GENERAL SAFETY PRECAUTIONS

Cutting equipment designed to reduce kickback

WARNING! Faulty cutting equipment or the

! wrong combination of bar and saw chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well-maintained you can reduce the effects of kickback.

Bar

The smaller the tip radius the lower the chance of kickback.

Chain

A chain is made up of a number of links, which are available in standard and low-kickback versions.

IMPORTANT! No saw chain design eliminates the danger of kickback.

!

WARNING! Any contact with a rotating saw

chain can cause extremely serious injuries.

 

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.

Bar

•Length (inches/cm)

•Number of teeth on bar tip sprocket (T).

•Chain pitch (inches).The spacing between the drive links of the chain must match the spacing of the teeth on the bar tip sprocket and drive sprocket.

•Number of drive links. The number of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar tip sprocket.

•Bar groove width (inches/mm). The groove in the bar must match the width of the chain drive links.

•Chain oil hole and hole for chain tensioner. The bar must be matched to the chain saw design.

Chain

•Chain pitch (inches)

•Drive link width (mm/inches)

•Number of drive links.

Sharpening your chain and adjusting depth gauge setting

General information on sharpening cutting teeth

•Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small. If the chain is very blunt it will produce wood powder and no chips or shavings.

•A sharp chain eats its way through the wood and produces long, thick chips or shavings.

12 – English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents EPA III TrioBrake KEY to Symbols Symbols on the machineSymbols in the operator’s manual You will find the following labels on your chain saw EPAContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackGeneral advice on adjusting depth gauge setting If the depth gauge setting is too largeAdjustment of depth gauge setting Tensioning the chainBar and cause serious or even fatal injury 346XP TrioBrake, 353 TrioBrakeLubricating cutting equipment Filling with chain oilChecking chain lubrication Chain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chain346XP TrioBrake, 353 TrioBrake 345e TrioBrakeAssembly Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Cutting Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor High speed jet HChecking the right-hand brake trigger Checking the brake triggerMuffler Starter Changing a broken or worn starter cordTensioning the recoil spring 345eReplacement of broken recoil and drive disc springs Air filterSpark plug Fitting the starterAdjustment of the oil pump When making adjustmentsLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderHeated handles Electrical carburetor heatingMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gauges050/1,3 mm 058/1,5 mmFederal Emission Control Warranty Statement ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions1151438-95
Top Page Image Contents