Husqvarna 353 EPA III TrioBrake, 1151438-95 Lubricating cutting equipment, Filling with chain oil

Page 15

GENERAL SAFETY PRECAUTIONS

Adjust the tension on the chain by turning the wheel down (+) for tighter tension and up (-) to loosen the tension.

Tighten the bar clutch by turning the knob clockwise.

Fold the knob back in to lock the tensioning.

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

! equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

Filling with chain oil

All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburetor as recommended (a lean mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil).

Checking chain lubrication

Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

Check that the oil channel in the bar is not obstructed. Clean if necessary.

Check that the groove in the edge of the bar is clean. Clean if necessary.

English 15

Image 15
Contents EPA III TrioBrake KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingIf the depth gauge setting is too large General advice on adjusting depth gauge setting346XP TrioBrake, 353 TrioBrake Adjustment of depth gauge settingTensioning the chain Bar and cause serious or even fatal injuryLubricating cutting equipment Filling with chain oilChecking chain lubrication Chain drive sprocket Needle bearing lubricationChecking wear on cutting equipment 345e TrioBrake AssemblyFitting the bar and chain 346XP TrioBrake, 353 TrioBrakeAssembly Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Basic cutting technique TermsLimbing Cutting Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral High speed jet H Correctly adjusted carburetorChecking the brake trigger Checking the right-hand brake triggerMuffler 345e StarterChanging a broken or worn starter cord Tensioning the recoil springFitting the starter Replacement of broken recoil and drive disc springsAir filter Spark plugNeedle bearing lubrication Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketElectrical carburetor heating Air Injection centrifugal cleaningTemperature 0C 32F or colder Heated handlesDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Bar and chain combinationsSaw chain filing and file gauges 050/1,3 mmObligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautions1151438-95