Husqvarna 967277601 warranty Adjusting the Mower Deck, Leveling deck

Page 45

MAINTENANCE

Adjusting the Mower Deck

Leveling deck

Adjust the deck while the mower is on a level surface. Make sure the tires are inflated to the correct pressure. See Technical Data / Transmission. If tires are under or over inflated, the deck cannot be properly adjusted. Raise the deck to the highest (transport) position.

The deck should be adjusted slightly higher in the rear.

NOTE: To insure accuracy of leveling procedure, mower deck drive belt must be installed prior to leveling deck.

1.Wear heavy gloves. Turn each outer blade tip to align side to side.

2.Measure from the floor surface up to the bottom of the blade tip on the discharge side of the mower deck. Record this measurement.

3.Move to the opposite side, check that the measurement is the same. If adjustment is required—with a ¾" or adjustable wrench, turn the lift link adjustment nuts on either side counter clockwise to lower or clockwise to raise. Adjust until both side-to-side measurements are equal.

4.Turn either blade to align with the deck front-to- rear. If the front blade tip does not measure 1/8" to ½" higher in the rear, follow the front adjustment instructions that follow.

5.With a 5/8 or adjustable wrench, turn the nuts on the front suspension linkage. Clockwise raises the front of the mower, counterclockwise will lower the front. Adjust nuts until rear of mower deck is positioned level to 1/8" higher in the rear than the side-to-side measurement.

NOTE: This will place the mower deck in a standard measurement position. Depending on the type of grass being mowed or environmental conditions, additional adjustments may be required to achieve the desired cut.

80158-166

Set blades to begin alignment

8058-030

Lift link adjustment nut

8058-031

Deck front adjustment nuts

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Operator Manual All rights reserved Contents Page Introduction Manufacturing Number Good ServiceXxxx xxxxxx xxxxx xxxx Xxxxxx xxxxxxxxx. xx xxxxxxxx Symbols and DecalsShut off engine before Performing any Safety Safety InstructionsGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline General Maintenance Risk of sparking Safety System Spark Arrestor TransportControl Locations ControlsSteering Control Levers Park Brake Throttle ControlCold Weather Control Blade Switch Ignition SwitchSmartSwitch Courtesy Buttons Seat Adjustment Lever Service MinderSeat should not be adjusted while unit is in motion Tracking KnobFuel Tank FuseFuel Shut Off Valve Cutting Height AdjusterBypass Linkages Always raise the deck to the highest position for transportOperation TrainingSteering Resetting ignition system passcode SmartSwitch IgnitionBefore Starting Starting the Engine Place controls in neutral position Full throttle position Important Information Ignition System Faults Running Stopping the Engine Operating On Hills Mowing Tips Headlights Weak BatteryJumper Cables Use To remove cables, reverse orderBattery Voltage Light Checking Battery Charge SystemMoving Machine By Hand Maintenance Schedule MaintenanceBefore After Year Replacing battery BatterySteering controls locked in neutral Tire Pressures Removal and installation of caster wheelAnti-scalp Rollers Caster WheelsDeck Belt Installation BeltsDeck Belt Removal Cutting Blades Leveling deck Adjusting the Mower DeckCleaning Use protective glasses when cleaning and washingHardware Lubrication Lubrication ScheduleGeneral Transmission Wheel and Deck ZerksFront Wheel Mount Front Wheel BearingsProblem Cause TroubleshootingTroubleshooting Service StorageWinter Storage Schematic Torque Specifications Technical DataAccessories Standard HardwareEngine DimensionsTransmission FrameUSA requirements Conformity CertificatesDelivery Service Service JournalAfter the First 10 Hours Hour ServicePerform the 25-hour service At Least Once Each Year Service Journal Service Journal Service Journal Page 115 646927 Rev a 2013-10-15

967277601 specifications

The Husqvarna 967277601 is a high-performance chainsaw designed for both professional and avid homeowners who require reliable tools for their outdoor projects. This model stands out due to its powerful engine, advanced features, and ergonomic design, making it suitable for a range of cutting tasks, from felling trees to pruning branches.

One of the primary attributes of the Husqvarna 967277601 is its potent engine. Equipped with a robust two-stroke engine, this chainsaw delivers impressive horsepower, facilitating efficient cutting and reducing the risk of bogging down even in dense wood. The air injection technology enhances the engine's performance by utilizing centrifugal force to remove larger debris particles from the air intake before they reach the air filter. This feature not only prolongs the life of the air filter but also improves fuel efficiency and reduces emissions.

The chainsaw incorporates a lightweight yet durable design that makes it easy to maneuver during operation. The design embraces components constructed from high-quality materials, ensuring both resilience and comfort. A comfortable grip is essential for extended use, and Husqvarna recognizes this need. The anti-vibration system significantly reduces the impact of vibrations on the operator’s hands, allowing for longer working periods without fatigue.

Husqvarna 967277601 features a user-friendly starting system. The Smart Start technology allows for easy starting with minimal effort, which is especially beneficial when working in demanding conditions. The chainsaw also includes an adjustable oil pump that enhances chain lubrication while conserving oil as needed. This ensures optimal performance and longevity of the cutting system while maintaining environmentally responsible practices.

In terms of safety, the model is equipped with features such as a chain brake, which activates automatically when a sudden kickback occurs, protecting the user from injury. The easily accessible controls enhance safety as well, allowing operators to manage the saw’s functions safely.

Overall, the Husqvarna 967277601 chainsaw embodies a perfect synergy of power, innovative technology, and user-friendly features, positioning it as an ideal choice for individuals seeking efficiency and reliability in their cutting tools. Whether for heavy-duty tasks or light garden maintenance, this chainsaw meets a variety of needs while ensuring operator comfort and safety.
Top Page Image Contents