Husqvarna 967277601 warranty Battery, Replacing battery

Page 40

MAINTENANCE

Battery

Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

See chart for charging times.

CAUTION!

Always wear eye protection when around batteries.

Cleaning battery and terminals

Corrosion and dirt on the battery and terminals can cause the battery to lose power.

1.Open the terminal access doors.

2.Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine.

3.Rinse the battery with plain water and dry.

4.Clean terminals and battery cable ends with wire brush until shiny.

5.Coat terminals with grease or petroleum jelly.

6.Reinstall battery.

Replacing battery

1.Lift seat and rotate forward.

2.Using two ½" wrenches disconnect BLACK battery cable then RED battery cable.

3.Position deck to lowest setting.

4.Front underside of frame, remove the nuts that secure the battery hold-down.

5.Carefully remove the battery from the mower.

6.Install new battery with terminals in the same position as the old battery.

7.Reinstall battery hold-down and secure with nuts removed in Step 4.

8.Reconnect RED battery cable to positive (+) battery terminal with bolt and hex nut.

9.Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut

10.Replace terminal boot cover.

11.Lower seat

STANDARD

STATE

APPROXIMATE BATTERY CHARGING TIME*

 

 

TO FULL CHARGE AT 80OF / 27OC

BATTERY

OF

 

 

 

 

 

Maximum Rate at:

 

 

 

 

 

 

CHARGE

 

 

 

 

 

50 Amps

30 Amps

20 Amps

10 Amps

 

 

 

 

 

 

 

 

12.6V

100%

- FULL CHARGE -

 

 

 

 

 

 

12.4V

75%

20 min.

35 min.

48 min.

90 min.

 

 

 

 

 

 

12.2V

50%

45 min.

75 min.

95 min.

180 min.

 

 

 

 

 

 

12.0V

25%

65 min.

115 min.

145 min.

280 min.

 

 

 

 

 

 

11.8V

0%

85 min.

150 min.

195 min.

370 min.

 

 

 

 

 

 

*Charging time depends on battery capacity,

condition, age, temperature and efficiency of charger

IMPORTANT INFORMATION

Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws.

WARNING!

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparks from accidental grounding.

8050-109

Remove battery hold-down to replace battery

40

Image 40
Contents Operator Manual All rights reserved Contents Page Introduction Good Service Manufacturing NumberSymbols and Decals Xxxx xxxxxx xxxxx xxxx Xxxxxx xxxxxxxxx. xx xxxxxxxxShut off engine before Performing any Safety Instructions SafetyGeneral Operation Never take passengers Personal Safety Equipment Slope OperationChildren Safe Handling of Gasoline General Maintenance Risk of sparking Safety System Transport Spark ArrestorControls Control LocationsSteering Control Levers Throttle Control Park BrakeCold Weather Control Ignition Switch Blade SwitchSmartSwitch Courtesy Buttons Service Minder Seat Adjustment LeverSeat should not be adjusted while unit is in motion Tracking KnobFuse Fuel TankCutting Height Adjuster Fuel Shut Off ValveBypass Linkages Always raise the deck to the highest position for transportTraining OperationSteering SmartSwitch Ignition Resetting ignition system passcodeBefore Starting Starting the Engine Place controls in neutral position Full throttle position Important Information Ignition System Faults Running Stopping the Engine Operating On Hills Mowing Tips Weak Battery HeadlightsJumper Cables Use To remove cables, reverse orderChecking Battery Charge System Battery Voltage LightMoving Machine By Hand Maintenance Maintenance ScheduleBefore After Year Battery Replacing batterySteering controls locked in neutral Removal and installation of caster wheel Tire PressuresAnti-scalp Rollers Caster WheelsBelts Deck Belt InstallationDeck Belt Removal Cutting Blades Adjusting the Mower Deck Leveling deckUse protective glasses when cleaning and washing CleaningHardware Lubrication Schedule LubricationGeneral Wheel and Deck Zerks TransmissionFront Wheel Mount Front Wheel BearingsTroubleshooting Problem CauseTroubleshooting Storage ServiceWinter Storage Schematic Technical Data Torque SpecificationsAccessories Standard HardwareDimensions EngineTransmission FrameConformity Certificates USA requirementsService Journal Delivery ServiceHour Service After the First 10 HoursPerform the 25-hour service At Least Once Each Year Service Journal Service Journal Service Journal Page 115 646927 Rev a 2013-10-15

967277601 specifications

The Husqvarna 967277601 is a high-performance chainsaw designed for both professional and avid homeowners who require reliable tools for their outdoor projects. This model stands out due to its powerful engine, advanced features, and ergonomic design, making it suitable for a range of cutting tasks, from felling trees to pruning branches.

One of the primary attributes of the Husqvarna 967277601 is its potent engine. Equipped with a robust two-stroke engine, this chainsaw delivers impressive horsepower, facilitating efficient cutting and reducing the risk of bogging down even in dense wood. The air injection technology enhances the engine's performance by utilizing centrifugal force to remove larger debris particles from the air intake before they reach the air filter. This feature not only prolongs the life of the air filter but also improves fuel efficiency and reduces emissions.

The chainsaw incorporates a lightweight yet durable design that makes it easy to maneuver during operation. The design embraces components constructed from high-quality materials, ensuring both resilience and comfort. A comfortable grip is essential for extended use, and Husqvarna recognizes this need. The anti-vibration system significantly reduces the impact of vibrations on the operator’s hands, allowing for longer working periods without fatigue.

Husqvarna 967277601 features a user-friendly starting system. The Smart Start technology allows for easy starting with minimal effort, which is especially beneficial when working in demanding conditions. The chainsaw also includes an adjustable oil pump that enhances chain lubrication while conserving oil as needed. This ensures optimal performance and longevity of the cutting system while maintaining environmentally responsible practices.

In terms of safety, the model is equipped with features such as a chain brake, which activates automatically when a sudden kickback occurs, protecting the user from injury. The easily accessible controls enhance safety as well, allowing operators to manage the saw’s functions safely.

Overall, the Husqvarna 967277601 chainsaw embodies a perfect synergy of power, innovative technology, and user-friendly features, positioning it as an ideal choice for individuals seeking efficiency and reliability in their cutting tools. Whether for heavy-duty tasks or light garden maintenance, this chainsaw meets a variety of needs while ensuring operator comfort and safety.