Husqvarna 5525PW warranty Lawn Mower, Tires, Drive Wheels, Blade Care

Page 11

MAINTENANCE

LAWN MOWER

Always observe safety rules when performing any main- tenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chem- icals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check wheels each time before you mow to be sure they move freely.

The wheels not turning freely means trash, grass cuttings, etc. are in the drive wheel or dust cover area and must be cleaned to free drive wheels. If necessary to clean the drive wheels, be sure to clean all wheels.

1.Remove hubcaps, locknuts and washers.

2.Remove wheels from wheel adjusters.

3.Remove any trash or grass cuttings from inside the dust cover, pinion and/or drive wheel gear teeth.

4.Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely, contact a qualified service center.

BLADE CARE

For best results, mower blade must be kept sharp. Replace bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE (See Fig. 12)

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter-clockwise.

5.Remove blade and attaching hardware (bolt, lock washer and hardened washer).

6.Remove debris shield.

NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE (See Fig. 12)

1. Position the blade adapter on the engine crankshaft. Be sure key in adapter and crankshaft keyway are aligned; and that the drive belt is inside the tab of the belt retainer.

11

2.Install debris shield.

3.Position blade on the blade adapter.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON BLADE ADAPTER.

4.Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine.

5.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

6.Use block of wood between blade and lawn mower hous- ing and tighten the blade bolt, turning clockwise.

•The recommended tightening torque is 35–40 ft. lbs.

IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS REPLACING, REPLACE ONLY WITHAPPROVED BOLT.

BLADE

CRANK-

SHAFT

ADAPTER

KEYWAY

 

BELT

 

RETAINER

 

 

KEY

DEBRIS

TRAILING

EDGE

SHIELD

 

HARDENED

BLADE

WASHER

 

 

LOCK WASHER

 

BLADE BOLT

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. An unbalanced blade will cause eventual damage to lawn mower or engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

CENTER HOLE

5/8" BOLT OR PIN

BLADE

FIG. 13

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operator’s Manual Manual de Operario II. General Operation Safety RulesChildren Table of Contents Customer Responsibilities AssemblyProduct Specifications HOW to SET UP Your Lawn MowerTighten T-knob Install Starter Rope See FigTo Install Attachments To Assemble Grass Catcher See FigKnow Your Lawn Mower Meets Cpsc Safety RequirementsOperation Engine Zone Control HOW to USE Your Lawn MowerEngine Speed ADD OIL See Fig Before Starting EngineTo Convert Mower To Empty Grass Catcher See FigMulching Mowing Tips To Stop EngineTo Start Engine Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsBlade Care Lawn MowerTires Drive WheelsTo Change Engine OIL See Fig EngineGrass Catcher Gear CasesMuffler CleaningWater Washout Feature See Fig IN-LINE Fuel Filter See FigTo Remove Drive Belt See Figs Service and AdjustmentsTo Adjust Cutting Height Rear DeflectorFront To Replace Drive Belt See FigsHandle See Figs To Adjust Handle See FigStorage CarburetorCylinder OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Consumer Wheeled Limited Warranty Chart II. Operacion Reglas DE SeguridadNiños Servicio Tabla DE MateriasIII. Operacion Sobre LAS Cuestas IV. Manejo Seguro DE GasolinaComo Preparar SU Segadora Montaje / PRE-OPERACIÓNEspecificaciones DEL Producto Responsabilidades DEL ClientePara Instalar LOS Accesorios Para Montar EL Recogedor DE Césped Vea FigInstalación DEL Cordón Arrancador Vea Fig Cumple CON LOS Requisitos DE Seguridad DE LA Cpsc OperaciónFamiliarícese CON SU Segadora Control DE Zona DEL Motor Como Usar SU SegadoraVelocidad DEL Motor Agregue Aceite Vea Fig Para Convertir LA SegadoraAntes DE Hacer Arrancar EL Motor Para Vaciar EL Recogedor DE Césped Vea FigConsejos Para Segar Para Parar EL MotorPara Hacer Arrancar EL Motor Consejos Para Segar Y AcolcharLubricación MantenimientoRecomendaciones Generales Antes DE Cada USOCuidado DE LA Cuchilla SegadoraLlantas Ruedas DE ImpulsiónPara Cambiar EL Aceite DEL Motor Vea Fig MotorRecogedor DE Césped Cajas DE EngranajesBujía LimpiezaFiltro DE Combustible Vea Fig SilenciadorPara Remover Correa DE Impulsión Vea Figs y Servicio Y AjustesPara Ajustar LA Altura DE Corte Desviador TraseroFrente Para Cambiar Correa DE Impulsión Vea Figs yMango Vea Figs y AlmacenamientoPara Ajustar EL Mango Vea Fig CarburadorCilindro OtrosSistema DE Combustible Aceite DEL MotorProblema Causa Corrección Solución DE ProblemasProductos con ruedas para consumidor Garantía limitada Cómo Obtener Servicio 575 49 43-01 W 2012 IR Consumidor Comercial Alquiler 03/03/2014 by
Related manuals
Manual 30 pages 21.92 Kb

5525PW specifications

Husqvarna, a renowned name in outdoor power equipment, offers an array of high-performance chainsaws, including the 6026PW, 9030PW, 1335PW, and 5525PW models. Each model is designed to cater to various cutting needs, making them suitable for both professional and amateur users.

The Husqvarna 6026PW boasts a robust engine, specifically designed for heavy-duty use. With its powerful air-cooled two-stroke engine, this model delivers exceptional cutting performance while maintaining low levels of vibration, which reduces user fatigue during extended use. The integrated air filter system prolongs the lifespan of the engine, ensuring it operates efficiently under demanding conditions.

The 9030PW model stands out for its advanced technology and ease of use. It features an automatic oiler system that ensures consistent lubrication of the chain, enhancing both performance and longevity. The 9030PW also benefits from an ergonomic design, which includes an adjustable handle for optimal comfort and control. This model's lightweight construction makes it easy to maneuver, perfect for detailed trimming or larger cutting tasks.

The Husqvarna 1335PW is designed with the homeowner in mind, offering a perfect balance of power and finesse. One of its defining features is the X-Torq engine, which provides higher torque over a wider RPM range while also reducing fuel consumption and emissions. The 1335PW also includes a quick-release air filter for easy cleaning and maintenance, ensuring your chainsaw remains in peak condition.

Finally, the Husqvarna 5525PW combines strength and versatility, making it suitable for a diverse range of cutting applications. This model features a durable chain brake for added safety, helping to prevent accidents during operation. The 5525PW's easy-to-start system minimizes starting effort, allowing users to get to work quickly without hassle.

All four models benefit from Husqvarna's commitment to user safety and comfort, making them ideal for both professionals and DIY enthusiasts. With innovative features and robust design, the Husqvarna 6026PW, 9030PW, 1335PW, and 5525PW represent the perfect blend of performance, durability, and technology, carving out a niche for themselves in the competitive chainsaw market.
Top Page Image Contents