HOW to USE Your Lawn Mower, Engine Speed | Husqvarna 5525PW specification

OPERATION

The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask over spectacles.

Use ear pro- t e c t o r s t o avoid damage to hearing.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

The engine speed was set at the factory for optimum per- formance. Speed is not adjustable.

ENGINE ZONE CONTROL

CAUTION: Federal regulations require an engine control to be installed on this lawn mower in order to minimize the risk of blade contact injury. Do not under any circumstances attempt to defeat the function of the operator control. The blade turns when the engine is running.

•Your lawn mower is equipped with an operator presence control bar which requires the operator to be positioned behind the mower handle to start and operate the mower.

DRIVE CONTROL (See Fig. 5)

•Self-propelling is controlled by holding the operator presence control bar down to the handle and pulling the drive control bar up to the handle. The closer to the handle the bar is pulled, the faster the unit will travel.

•Forward motion will stop when either the operator pres- ence control bar or drive control bar are released. To stop forward motion without stopping engine, release the drive control bar only. Hold operator presence control bar down against handle to continue mowing without self-propelling.

NOTE: If after releasing the drive control the mower will not roll backwards, push the mower forward slightly to disengage drive wheels.

DRIVE CONTROL ADJUSTMENT (See Fig. 6)

Over time, the drive control system may become “loose”, resulting in decreased speed. There is an adjustment turnbuckle on the drive control cable to increase tension on the drive belt. Proceed as follows:

1.Turn unit off and disconnect spark plug wire from spark plug.

NOTE: Your mower is shipped with no “gap” between drive control cable and jam nut.

2.To increase drive speed, rotate turnbuckle on drive control cable until there is a small “gap” between drive control cable and jam nut.

3.Operate mower to test drive speed. Readjust as re- quired.

IMPORTANT: OVER-ADJUSTMENT WILL MAKE IT DIFFICULT TO LIFT CONTROL BAR TO HANDLE AND WILL CAUSE YOUR MOWER TO "CREEP" FORWARD WHEN CONTROL BAR IS RELEASED.

4. Tighten jam nut against turnbuckle.

If condition fails to improve after the above steps (forward
speed remains the same), your drive belt is worn and
should be replaced.	7

OPERATOR	DRIVE
PRESENCE	DRIVE
CONTROL BAR	CONTROL BAR
DRIVE CONTROL	DRIVE CONTROL
ENGAGED	DISENGAGED

FIG. 5

ORIGINAL FACTORY SETTING

(NO “GAP”)

JAM NUT

TURNBUCKLE

DRIVE CONTROL

CABLE

“GAP” WHILE

ADJUSTING

“GAP” AFTER ADJUSTMENT

FIG. 6

TO ADJUST CUTTING HEIGHT (See Fig. 7)

Raise wheels for low cut and lower wheels for high cut, adjust cutting height to suit your requirements. Medium position is best for most lawns.

•To change cutting height, squeeze adjuster lever toward wheel. Move wheel up or down to suit your require- ments. Be sure all wheels are in the same setting.

NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever. Also, 9-position adjusters (if so equipped) allow lever to be positioned between the plate tabs.

ROTATE LEVER TOWARD ENGINE

TO LOWER MOWER

PLATE

TAB

LEVER

ROTATE LEVER AWAY FROM ENGINE TO RAISE MOWER

FIG. 7

5525PW specifications

Husqvarna, a renowned name in outdoor power equipment, offers an array of high-performance chainsaws, including the 6026PW, 9030PW, 1335PW, and 5525PW models. Each model is designed to cater to various cutting needs, making them suitable for both professional and amateur users.

The Husqvarna 6026PW boasts a robust engine, specifically designed for heavy-duty use. With its powerful air-cooled two-stroke engine, this model delivers exceptional cutting performance while maintaining low levels of vibration, which reduces user fatigue during extended use. The integrated air filter system prolongs the lifespan of the engine, ensuring it operates efficiently under demanding conditions.

The 9030PW model stands out for its advanced technology and ease of use. It features an automatic oiler system that ensures consistent lubrication of the chain, enhancing both performance and longevity. The 9030PW also benefits from an ergonomic design, which includes an adjustable handle for optimal comfort and control. This model's lightweight construction makes it easy to maneuver, perfect for detailed trimming or larger cutting tasks.

The Husqvarna 1335PW is designed with the homeowner in mind, offering a perfect balance of power and finesse. One of its defining features is the X-Torq engine, which provides higher torque over a wider RPM range while also reducing fuel consumption and emissions. The 1335PW also includes a quick-release air filter for easy cleaning and maintenance, ensuring your chainsaw remains in peak condition.

Finally, the Husqvarna 5525PW combines strength and versatility, making it suitable for a diverse range of cutting applications. This model features a durable chain brake for added safety, helping to prevent accidents during operation. The 5525PW's easy-to-start system minimizes starting effort, allowing users to get to work quickly without hassle.

All four models benefit from Husqvarna's commitment to user safety and comfort, making them ideal for both professionals and DIY enthusiasts. With innovative features and robust design, the Husqvarna 6026PW, 9030PW, 1335PW, and 5525PW represent the perfect blend of performance, durability, and technology, carving out a niche for themselves in the competitive chainsaw market.