Husqvarna PZ5426 FX, 966062201, 966061401, 966060901 Safety Instructions, General Operation

Page 9

SAFETY

Safety Instructions

These instructions are for your safety. Read them carefully.

WARNING!

This symbol means that important safety instructions need to be emphasized. It concerns your safety.

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

General Operation

Read, understand, and follow all instructions on the machine and in the manual before starting.

Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.

Only allow responsible adults, who are familiar with the instructions, to operate the machine.

Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades.

Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.

Never carry passengers. The machine is only intended for use by one person.

Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.

Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.

Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working

Slow down before turning.

Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting.

Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge guard.

Operate machine only in daylight or good artificial light.

Do not operate the machine while under the influence of alcohol or drugs.

8011-512

Read the operator’s manual before starting the machine

8011-513

Clear the area of objects before mowing

9

Image 9
Contents Operator Manual Page Contents Page Introduction Manufacturing Number Good ServiceSymbols and decals Manual Performing any Safety Safety InstructionsGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline Safe Handling of Propane General Maintenance Risk of sparking Transport Spark Arrestors Rollover Protection System RopsControl Locations ControlsGas Engine EngineMotion Control Levers Tracking Knob Hour MeterBlade Switch Ignition SwitchParking Brake Ignition switch RUN position Fuses Choke ControlCutting Height Pedals Fuel Shut Off Valve Seat Adjustment LeverRefueling Propane Model Operation TrainingSteering Before Starting Roll Bar and Safety BeltStarting the Engine Gasoline engines only Turn fuel shut off valve counter clockwise to open Push choke in after starting Weak Battery Jumper CablesTo remove cables, reverse order Running Operating on Hills Ensure that no one is near mower when engaging blade switchStopping the Engine Mowing Tips Manual Transport Maintenance Maintenance Battery For cleaningFor replacing Fuel Filter Safety SystemTire Pressures Gasoline Engines OnlyParking brake adjustment Neutral Adjustments Deck Belt Installation Deck BeltDeck Belt Removal Pump Belt Belt InstallationBelts Replacing Pump BeltCutting Blades Leveling Deck Adjusting the Mower DeckDeck Lift Spring Anti-scalp RollersRemoval and Installation CleaningUse protective glasses when cleaning and washing Caster WheelsLubrication Lubrication ScheduleGeneral Cables Wheel and Deck ZerksFront Wheel Mount Front Wheel BearingsFluid Change Hydraulic DrivePurging Procedures Problem Cause Troubleshooting guideTroubleshooting guide Service StorageWinter Storage Wiring Diagram Technical Data PZ 5426FX PZ6030CV EngineTransmission PZ 5426FX PZ6030CV Frame DimensionPZ6029FX PZ7234FX Engine PZ6029FX PZ7234FX Frame FX801V LP PZ6029PFX EnginePZ6029PFX Frame Hex Head Cap Screws Torque SpecificationsStandard Hardware Metric Standard HardwareCE requirements USA requirementsDelivery Service Service JournalAction Stamp, signDate, mtr reading Stamp, sign After 10 hoursDaily Service Hour Service Service Journal Service Journal At least once each year Action Date, mtr reading Stamp, sign Service Journal Service Journal Service Journal Page 115 254426 R1 09/14/09