Husqvarna 372 XPG manual Tensioning the chain

Page 14

GENERAL SAFETY PRECAUTIONS

File all the teeth to the same length. When the length of the cutting teeth is reduced to 5/32 inch (4 mm) the chain is worn out and should be replaced.

min 4 mm (5/32")

General advice on adjusting depth gauge setting

When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

 

!

WARNING! The risk of kickback is

 

increased if the depth gauge setting is

 

 

 

 

too large!

 

 

 

Adjustment of depth gauge setting

The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off

! the bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

14 – English

Image 14
Contents Special 372 XP 372 XPG Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping system Stop switchCutting equipment MufflerChain Cutting equipment designed to reduce kickbackBar Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Checking chain lubrication Lubricating cutting equipmentFilling with chain oil Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentWorking with the chain AssemblyFitting the bar and chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment High speed jet H Fine adjustment of the idling speed TCorrectly adjusted carburetor Checking brake band wearChecking the inertia brake release ImmediatelyMuffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil spring Air filterSpark plug Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Saw chain filing and file gauges050/1,3 mm Your cutting needFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Control Warranty Parts List Kickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsOriginal instructions 1153180-95

372 XPG specifications

The Husqvarna 372 XPG is a powerful, professional-grade chainsaw that stands out in the market due to its superior performance and innovative technology. Designed for demanding tasks such as logging, tree felling, and heavy-duty pruning, the 372 XPG boasts impressive features that cater to professionals seeking reliability and efficiency.

One of the most notable attributes is its robust engine. The 372 XPG is equipped with a 70.1 cc X-Torq engine that delivers exceptional power. This engine design not only optimizes power output but also reduces fuel consumption and emissions, aligning with modern environmental standards. The chainsaw achieves up to 4.8 kW of power, enabling users to tackle the toughest cutting jobs with ease.

Modern technology is incorporated into the 372 XPG to enhance user experience and usability. The chainsaw features the Smart Start system, which allows for effortless starting with minimal resistance on the starter cord. This is especially beneficial for professionals who need to get the job done quickly without the frustration of a difficult start.

Another key feature is the LowVib system, which significantly reduces vibrations during operation. This technology is crucial for minimizing operator fatigue, allowing users to work for extended periods without discomfort. The ergonomic design, combined with a comfortable handle, further enhances user control and precision while cutting.

Durability is a hallmark of the Husqvarna 372 XPG. Constructed with high-quality materials, this chainsaw can withstand the rigors of professional use. Its air filtration system is designed for efficient dust and debris removal, extending the life of the engine and maintaining optimal performance over time.

Safety features are also paramount with this model. It includes a chain brake that activates instantaneously in the event of kickback, ensuring the operator's safety during use.

Overall, the Husqvarna 372 XPG combines power, technology, and durability, making it a favorite among professionals in various cutting applications. Its balanced design, advanced engine, and safety features ensure that it not only meets but exceeds expectations, underscoring Husqvarna's reputation for quality and innovation in outdoor power equipment. Whether you are a professional logger or a landscape contractor, the 372 XPG is engineered to help you achieve your goals effectively and efficiently.