Husqvarna 372 XPG manual Fuel Handling

Page 18

FUEL HANDLING

Fuel

Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

 

!

WARNING! Always ensure there is

 

adequate ventilation when handling fuel.

 

 

 

 

 

Gasoline

•Use good quality unleaded gasoline.

•CAUTION! Engines equipped with catalytic converters must be run on unleaded fuel mixtures.

•Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose. The green fuel cap on saws fitted with catalytic converters means that only unleaded gasoline can be used.

•The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

•When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor).

Running-in

Avoid running at a too high speed for extended periods during the first 10 hours.

Two-stroke oil

•For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines.

•Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

•Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) for all engines.

Gasoline, litre

Two-stroke oil, litre

 

 

 

2% (1:50)

 

 

5

0,10

 

 

10

0,20

 

 

15

0,30

 

 

20

0,40

 

 

US gallon

US fl. oz.

 

 

1

2 1/2

 

 

2 1/2

6 1/2

 

 

5

12 7/8

 

 

Mixing

•Always mix the gasoline and oil in a clean container intended for fuel.

•Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

•Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

Chain oil

•We recommend the use of special oil (chain oil) with good adhesion characteristics.

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

18 – English

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Special 372 XP 372 XPG KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback BarChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Checking chain lubrication Lubricating cutting equipmentFilling with chain oil Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentAssembly Fitting the bar and chainWorking with the chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutHow to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral High speed jet H Fine adjustment of the idling speed TCorrectly adjusted carburetor Checking brake band wearChecking the inertia brake release ImmediatelyMuffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil spring Air filterSpark plug Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Saw chain filing and file gauges050/1,3 mm Your cutting needFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Control Warranty Parts List Kickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsOriginal instructions 1153180-95

372 XPG specifications

The Husqvarna 372 XPG is a powerful, professional-grade chainsaw that stands out in the market due to its superior performance and innovative technology. Designed for demanding tasks such as logging, tree felling, and heavy-duty pruning, the 372 XPG boasts impressive features that cater to professionals seeking reliability and efficiency.

One of the most notable attributes is its robust engine. The 372 XPG is equipped with a 70.1 cc X-Torq engine that delivers exceptional power. This engine design not only optimizes power output but also reduces fuel consumption and emissions, aligning with modern environmental standards. The chainsaw achieves up to 4.8 kW of power, enabling users to tackle the toughest cutting jobs with ease.

Modern technology is incorporated into the 372 XPG to enhance user experience and usability. The chainsaw features the Smart Start system, which allows for effortless starting with minimal resistance on the starter cord. This is especially beneficial for professionals who need to get the job done quickly without the frustration of a difficult start.

Another key feature is the LowVib system, which significantly reduces vibrations during operation. This technology is crucial for minimizing operator fatigue, allowing users to work for extended periods without discomfort. The ergonomic design, combined with a comfortable handle, further enhances user control and precision while cutting.

Durability is a hallmark of the Husqvarna 372 XPG. Constructed with high-quality materials, this chainsaw can withstand the rigors of professional use. Its air filtration system is designed for efficient dust and debris removal, extending the life of the engine and maintaining optimal performance over time.

Safety features are also paramount with this model. It includes a chain brake that activates instantaneously in the event of kickback, ensuring the operator's safety during use.

Overall, the Husqvarna 372 XPG combines power, technology, and durability, making it a favorite among professionals in various cutting applications. Its balanced design, advanced engine, and safety features ensure that it not only meets but exceeds expectations, underscoring Husqvarna's reputation for quality and innovation in outdoor power equipment. Whether you are a professional logger or a landscape contractor, the 372 XPG is engineered to help you achieve your goals effectively and efficiently.
Top Page Image Contents