Husqvarna 365 EPA I, 372XP EPA II manual Basic cutting technique, General, Terms

Page 24

WORKING TECHNIQUES

8Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which can lead to a kickback.

Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting with a pulling chain. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. Cutting with a pulling chain gives the operator better control over the chain saw and the position of the kickback zone.

9Follow the instructions on sharpening and maintaining your bar and chain. When you replace the bar and chain use only combinations that are recommended by us. See instructions under the headings Cutting equipment and Technical data.

Basic cutting technique

WARNING! Never use a chain saw by holding

!it with one hand. A chain saw is not safely controlled with one hand. Always have a secure, firm grip around the handles with both hands.

General

•Always use full throttle when cutting!

•Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load, i.e. without any resistance from the chain during cutting, can lead to serious engine damage).

•Cutting from above = Cutting with a pulling chain.

•Cutting from below = Cutting with pushing chain.

Cutting with a pushing chain increases the risk of kickback. See instructions under the heading How to avoid kickback.

Terms

Cutting = General term for cutting through wood.

Limbing = Cutting branches off a felled tree.

Splitting = When the object you are cutting breaks off before the cut is complete.

There are five important factors you should consider before making a cut:

1Make sure the cutting equipment will not jam in the cut.

2Make sure the object you are cutting will not split.

3Make sure the chain will not strike the ground or any other object during or after cutting.

4 Is there a risk of kickback?

5Do the conditions and surrounding terrain affect how safely you can stand and move about?

Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension.

In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom.You need to support the object so that it will not trap the chain or split during cutting.

IMPORTANT! If the chain jams in the cut: stop the engine! Don’t try to pull the chain saw free. If you do you may be injured by the chain when the chain saw suddenly breaks free. Use a lever to open up the cut and free the chain saw.

The following instructions describe how to handle the common situations you are likely to encounter when using a chain saw.

24 – English

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operator’s manual KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesSharpening your chain and adjusting depth gauge setting ChainSome terms that describe the bar and chain General information on sharpening cutting teethGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingIf the depth gauge setting is too large Sharpening cutting teethTensioning the chain Lubricating cutting equipmentChain oil Filling with chain oilChecking chain lubrication Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentBar Assembly Fitting the bar and chainFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique GeneralTerms Limbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatFelling Directional cutsFelling cut General advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor High speed jet HChecking brake band wear Checking the front hand guardWhen the bar hits the stump the brake should be applied Checking the inertia brake releaseChecking the brake trigger Muffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAdjustment of the oil pump Air filterSpark plug Lubricating the bar tip sprocketAir Injection centrifugal cleaning Temperature -5C 23F or colderCooling system Winter useHeated handles Electrical carburetor heatingCanada Other countriesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges 050/1,3 mm058/1,5 mm Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage 1150836-95 ´z+Rse¶5S¨ ´z+Rse¶5S¨

372XP EPA II, 365 EPA I specifications

The Husqvarna 365 EPA I and 372XP EPA II are two powerful chainsaws designed for serious woodcutting enthusiasts and professionals alike. Known for their robust performance, advanced technologies, and ergonomic design, these models are built to handle demanding tasks with ease.

The Husqvarna 365 EPA I is celebrated for its reliability and efficiency. It features a high-performance X-Torq engine that reduces fuel consumption by 20% and emissions by 75%, making it an environmentally friendly choice. The engine delivers impressive power output, ensuring that the saw can tackle tough cuts without compromising performance. Weighing in at just over 12 pounds, the 365 provides a perfect balance of power and maneuverability.

One of the standout features of the 365 is its Air Injection centrifugal air cleaning system, which helps to keep the air filter cleaner for longer periods. This results in reduced maintenance and improved performance, allowing users to focus on their cutting tasks rather than worrying about frequent cleaning. The chainsaw is also equipped with an adjustable oil pump, providing the user with the ability to control lubrication for better chain life and efficiency.

On the other hand, the Husqvarna 372XP EPA II takes performance to the next level. It boasts a larger displacement engine than the 365, offering enhanced power for professional applications. With the same X-Torq technology, it combines power and fuel efficiency, making it a great tool for heavy-duty tasks such as felling large trees or bucking heavy logs.

The 372XP is designed with an emphasis on ergonomics, featuring a slim body and excellent weight distribution. This makes it comfortable to handle, even during prolonged use. The chainsaw also comes with an innovative Smart Start system, which reduces resistance in the starter cord, ensuring easier starts every time. The adjustable oil pump feature is retained, allowing for precision control over the amount of oil delivered to the chain.

Both models reflect Husqvarna's commitment to quality and innovation, featuring durable components built to withstand the rigors of professional use. With their combination of advanced engine technology, design ergonomics, and ease of use, the Husqvarna 365 EPA I and 372XP EPA II remain top choices among chainsaw users looking for reliable performance and longevity. Whether you're a seasoned professional or a dedicated amateur, these chainsaws provide the power and efficiency necessary for a wide range of cutting tasks.
Top Page Image Contents