Husqvarna Comprehensive Guide to 365 Carb Settings and Maintenance
Page 30

MAINTENANCE

General

The user must only carry out the maintenance and service work described in this manual.

IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer (retailer).

Carburetor adjustment

Due to existing environmental and emissions legislation your chain saw is equipped with movement limiters on the carburetor adjuster screws. These limit the adjustment possibilities to a maximum of a 1/2 turn.

1/2

1/2

Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions.

Function

•The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. The air/ fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine.

•The setting of the carburetor means that the engine is adapted to local conditions, for example, the climate, altitude, fuel and the type of 2-stroke oil.

•The carburetor has three adjustment controls:

-L = Low speed jet

-H = High speed jet

-T = Idle adjustment screw

TH

L

•The L and H-jets are used to adjust the supply of fuel to match the rate that air is admitted, which is controlled with the throttle. If they are screwed clockwise the air/fuel ratio becomes leaner (less fuel) and if they are turned anti- clockwise the ratio becomes richer (more fuel). A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed.

•The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic settings and running in

The basic carburetor settings are adjusted during testing at the factory. Avoid running at a too high speed for extended periods during the first 10 hours.

CAUTION! If the chain rotates while idling the T-screw must be turned anti-clockwise until the chain stops.

Rec. idle speed: 2700 rpm

Fine adjustment

When the machine has been ”run-in” the carburetor should be finely adjusted. The fine adjustment should be carried out by a qualified person. First adjust the L-jet, then the idling screw T and then the H-jet.

Conditions

•Before any adjustments are made the air filter should be clean and the cylinder cover fitted. Adjusting the carburetor while a dirty air filter is in use will result in a leaner mixture next time the filter is cleaned. This can give rise to serious engine damage.

•Do not attempt to adjust the L and H jets beyond either stop as this could cause damage.

•Now start the machine according to the starting instructions and let it warm up for 10 minutes.

•Place the machine on a flat surface so that the bar points away from you and so that the bar and chain do not come into contact with the surface or other objects.

Low speed jet L

Turn the low speed jet L clockwise until it stops. If the engine accelerates poorly or idles unevenly, turn the low speed jet L anticlockwise until good acceleration and idling are achieved.

Fine adjustment of the idling speed T

Adjust the idle speed with the T-screw. If it is necessary to re- adjust, turn the T-screw clockwise while the engine is running, until the chain starts to rotate. Then turn counter-clockwise until the chain stops. A correctly adjusted idle speed setting occurs when the engine runs smoothly in every position. It should also be good margin to the rpm when the chain starts to rotate.

WARNING! Contact your servicing dealer, if

!the idle speed setting cannot be adjusted so that the chain stops at idle. Do not use the chain saw until it has been properly adjusted or repaired.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Operator’s manual KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSome terms that describe the bar and chain Sharpening your chain and adjusting depth gauge settingChain General information on sharpening cutting teethIf the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Sharpening cutting teethChain oil Tensioning the chainLubricating cutting equipment Filling with chain oilNeedle bearing lubrication Checking chain lubricationChain drive sprocket Checking wear on cutting equipmentBar Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique GeneralTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking brake band wear Correctly adjusted carburetorHigh speed jet H Checking the front hand guardWhen the bar hits the stump the brake should be applied Checking the inertia brake releaseChecking the brake trigger Muffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springSpark plug Adjustment of the oil pumpAir filter Lubricating the bar tip sprocketCooling system Air Injection centrifugal cleaningTemperature -5C 23F or colder Winter useCanada Heated handlesElectrical carburetor heating Other countriesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataSaw chain filing and file gauges 050/1,3 mm058/1,5 mm Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage 1150836-95 ´z+Rse¶5S¨ ´z+Rse¶5S¨

372XP EPA II, 365 EPA I specifications

The Husqvarna 365 EPA I and 372XP EPA II are two powerful chainsaws designed for serious woodcutting enthusiasts and professionals alike. Known for their robust performance, advanced technologies, and ergonomic design, these models are built to handle demanding tasks with ease.

The Husqvarna 365 EPA I is celebrated for its reliability and efficiency. It features a high-performance X-Torq engine that reduces fuel consumption by 20% and emissions by 75%, making it an environmentally friendly choice. The engine delivers impressive power output, ensuring that the saw can tackle tough cuts without compromising performance. Weighing in at just over 12 pounds, the 365 provides a perfect balance of power and maneuverability.

One of the standout features of the 365 is its Air Injection centrifugal air cleaning system, which helps to keep the air filter cleaner for longer periods. This results in reduced maintenance and improved performance, allowing users to focus on their cutting tasks rather than worrying about frequent cleaning. The chainsaw is also equipped with an adjustable oil pump, providing the user with the ability to control lubrication for better chain life and efficiency.

On the other hand, the Husqvarna 372XP EPA II takes performance to the next level. It boasts a larger displacement engine than the 365, offering enhanced power for professional applications. With the same X-Torq technology, it combines power and fuel efficiency, making it a great tool for heavy-duty tasks such as felling large trees or bucking heavy logs.

The 372XP is designed with an emphasis on ergonomics, featuring a slim body and excellent weight distribution. This makes it comfortable to handle, even during prolonged use. The chainsaw also comes with an innovative Smart Start system, which reduces resistance in the starter cord, ensuring easier starts every time. The adjustable oil pump feature is retained, allowing for precision control over the amount of oil delivered to the chain.

Both models reflect Husqvarna's commitment to quality and innovation, featuring durable components built to withstand the rigors of professional use. With their combination of advanced engine technology, design ergonomics, and ease of use, the Husqvarna 365 EPA I and 372XP EPA II remain top choices among chainsaw users looking for reliable performance and longevity. Whether you're a seasoned professional or a dedicated amateur, these chainsaws provide the power and efficiency necessary for a wide range of cutting tasks.
Top Page Image Contents