Husqvarna 365 EPA I Freeing a tree that has fallen badly, Freeing a trapped tree, General advice

Page 28

WORKING TECHNIQUES

We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. See instructions under the heading Technical data section to find out which lengths of bar are recommended for your saw.

There are methods for felling trees with a diameter larger than the bar length. However these methods involve a much greater risk that the kickback zone of the bar will come into contact with the tree.

Freeing a tree that has fallen badly

Freeing a ”trapped tree”

It is very dangerous to remove a trapped tree and there is high accident risk.

Never try to fell the tree that is trapped.

Never work in the risk zone of the hanging trapped tree.

The safest method is to use a winch.

•Tractor-mounted

•Portable

Cutting trees and branches that are in tension

Preparations: Work out which side is in tension and where the point of maximum tension is (i.e. where it would break if it was bent even more).

Decide which is the safest way to release the tension and whether you are able to do it safely. In complicated situations the only safe method is to put aside your chain saw and use a winch.

General advice:

Position yourself so that you will be clear of the tree or branch when the tension is released.

Make one or more cuts at or near the point of maximum tension. Make as many cuts of sufficient depth as necessary to reduce the tension and make the tree or branch break at the point of maximum tension.

Never cut straight through a tree or branch that is in tension!

If you must cut across tree/limb, make two to three cuts, one inch apart, one to two inches deep.

Continue to cut deeper until tree/limb bends and tension is released.

Cut tree/limb from outside the bend, after tension has been released.

28 – English

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Operator’s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesSharpening your chain and adjusting depth gauge setting ChainSome terms that describe the bar and chain General information on sharpening cutting teethGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingIf the depth gauge setting is too large Sharpening cutting teethTensioning the chain Lubricating cutting equipmentChain oil Filling with chain oilChecking chain lubrication Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentBar Assembly Fitting the bar and chainFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules General Basic cutting techniqueTerms Limbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFelling cut General advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Correctly adjusted carburetor High speed jet HChecking brake band wear Checking the front hand guardChecking the inertia brake release When the bar hits the stump the brake should be appliedChecking the brake trigger Muffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAdjustment of the oil pump Air filterSpark plug Lubricating the bar tip sprocketAir Injection centrifugal cleaning Temperature -5C 23F or colderCooling system Winter useHeated handles Electrical carburetor heatingCanada Other countriesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Saw chain filing and file gauges058/1,5 mm Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsPage 1150836-95 ´z+Rse¶5S¨ ´z+Rse¶5S¨

372XP EPA II, 365 EPA I specifications

The Husqvarna 365 EPA I and 372XP EPA II are two powerful chainsaws designed for serious woodcutting enthusiasts and professionals alike. Known for their robust performance, advanced technologies, and ergonomic design, these models are built to handle demanding tasks with ease.

The Husqvarna 365 EPA I is celebrated for its reliability and efficiency. It features a high-performance X-Torq engine that reduces fuel consumption by 20% and emissions by 75%, making it an environmentally friendly choice. The engine delivers impressive power output, ensuring that the saw can tackle tough cuts without compromising performance. Weighing in at just over 12 pounds, the 365 provides a perfect balance of power and maneuverability.

One of the standout features of the 365 is its Air Injection centrifugal air cleaning system, which helps to keep the air filter cleaner for longer periods. This results in reduced maintenance and improved performance, allowing users to focus on their cutting tasks rather than worrying about frequent cleaning. The chainsaw is also equipped with an adjustable oil pump, providing the user with the ability to control lubrication for better chain life and efficiency.

On the other hand, the Husqvarna 372XP EPA II takes performance to the next level. It boasts a larger displacement engine than the 365, offering enhanced power for professional applications. With the same X-Torq technology, it combines power and fuel efficiency, making it a great tool for heavy-duty tasks such as felling large trees or bucking heavy logs.

The 372XP is designed with an emphasis on ergonomics, featuring a slim body and excellent weight distribution. This makes it comfortable to handle, even during prolonged use. The chainsaw also comes with an innovative Smart Start system, which reduces resistance in the starter cord, ensuring easier starts every time. The adjustable oil pump feature is retained, allowing for precision control over the amount of oil delivered to the chain.

Both models reflect Husqvarna's commitment to quality and innovation, featuring durable components built to withstand the rigors of professional use. With their combination of advanced engine technology, design ergonomics, and ease of use, the Husqvarna 365 EPA I and 372XP EPA II remain top choices among chainsaw users looking for reliable performance and longevity. Whether you're a seasoned professional or a dedicated amateur, these chainsaws provide the power and efficiency necessary for a wide range of cutting tasks.
Top Page Image Contents