Husqvarna 340 EPA II, 345 EPA II, 350 EPAI manual Fuel Handling, Fuelmix

Page 26

FUEL HANDLING

Fuelmix

IMPORTANT! The chain saw is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

!Always provide for good ventilation when handling fuel.

Gasoline

•This engine is certified to operate on unleaded gasoline.

• Use good quality unleaded gasoline.

• The lowest recommended octane rating is 87. If you run the engine on lower octane rating than 87 so- called “knocking“ can occur. This leads to an increased engine temperature, which can result in a serious engine breakdown.

•When working at continuous high revs a higher octane rating is recommended.

Two-stroke oil

•For the best results use HUSQVARNA two-stroke oil, which is especially developed for chain saws. Mixing ratio 1:50 (2%).

•Never use two-stroke oil intended for water cooled outboard engines, so-called, outboard oil.

•Never use oil intended for four-stroke engines.

Gasoline

Oil

2%(1:50)

Lit.

Lit.

50,10

10

0,20

15

0,30

20

0,40

US

US

gallon

fl. oz.

12 1/2

2 1/2

6 1/2

512 7/8

Mixing

•Always mix the gasoline and oil in a clean container intended for fuel.

•Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

•Mix (shake) the fuel mixture thoroughly before filling the saw’s fuel tank.

•Do not mix more than max. one month’s supply of fuel.

•If the saw is not used for some time the fuel tank should be emptied and cleaned.

•This engine is certified to operate on unleaded gasoline.

Chain oil

•The chain lubrication system is automatic. Always use special chain oil with good adhesive characteristics.

•In countries where no special chain oil is available, EP 90 transmission oil can be used.

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right viscosity according to the air temperature.

•In temperatures below 0oC (32oF) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components.

•Contact your servicing dealer when choosing chain oil.

26 – English

Page 25 Page 27
Image 26
Page 25 Page 27
Contents EPA II 350 KEY to Symbols SymbolsContents EPASafety Instructions Chain SAW Safety EquipmentChain brake and front hand guard 3a StartingRight hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking the inertia brake release Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Risk of kickback is increased with a badly sharpened chainTensioning the chain General advice on setting raker clearanceSetting the raker clearance Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilChecking wear on cutting equipment Needle bearing maintenanceChecking chain lubrication Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Never use the saw one- handed General rulesDo not let go of the handles 10 ft General Safety PrecautionsMin m Basic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? What is what?340 AssemblyMounting guide bar and chain 345/350Fuel Handling Fuelmix10ft FuellingMin 3 m Start Start and StopStart and stop StopMaintenance CarburetorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springAir filter Needle bearing maintenanceAdjustment of the oil pump MufflerCooling system Centrifugal cleaning Air InjectionTemperature -5C or colder Winter useLong-term storage Weekly maintenance Daily maintenanceMonthly maintenance Technical Data 340 345 350Emission Control Warranty Statement Your Warranty Rights Obligations114 01 2002W49

345 EPA II, 340 EPA II, 345 EPA II, 350 EPAI specifications

Husqvarna, a renowned leader in the outdoor power equipment industry, offers a range of chainsaws designed for various needs and applications. Among their impressive lineup, the Husqvarna 340 EPA II, 345 EPA II, and 350 EPA I chainsaws stand out for their robust performance and innovative features.

The Husqvarna 340 EPA II is designed to cater to both homeowners and professionals. Its lightweight design, weighing only 4.9 kg, ensures maneuverability without sacrificing power. The chainsaw is powered by a 40.9 cc engine, providing ample power for tasks such as pruning, cutting firewood, and light felling. One key feature is its X-Torq engine technology, which optimizes fuel efficiency while reducing harmful emissions, ensuring compliance with environmental regulations. The ergonomic handle and low vibration design enhance user comfort during extended use.

Next, the Husqvarna 345 EPA II takes the essentials of the 340 and amps them up. With a slightly larger 45.7 cc engine, this chainsaw offers increased cutting power, making it ideal for homeowners who require more robust performance. The chainsaw features an automatic oiler for consistent lubrication of the chain, which prolongs the lifespan of the chain and bar. Additionally, the 345 EPA II incorporates an easy start system, allowing users to start the machine with minimal effort, making it a practical choice for all skill levels.

Finally, the Husqvarna 350 EPA I is built for seasoned professionals who demand high performance. Equipped with a powerful 50.1 cc engine, it delivers exhilarating cutting speeds for demanding applications. The chainsaw features advanced ignition systems that ensure quick starts and reliable performance in various conditions. One of the standout characteristics of the 350 EPA I is its Air Injection technology, which centrifugal forces remove dust and debris from the air intake. This filtration system helps maintain engine efficiency and prolongs service intervals.

All three models are equipped with Husqvarna's signature features, including easy access to air filters for maintenance and a chain brake for added safety. Their durable construction and advanced ergonomics make them versatile tools, whether for occasional use in residential settings or for tackling rigorous tasks in commercial environments. With a commitment to innovation and sustainability, Husqvarna's EPA II chainsaws continue to set the standard for performance and reliability in the outdoor power equipment industry.
Top Page Image Contents