Husqvarna 340 EPA II, 345 EPA II, 350 EPAI manual Weekly maintenance Daily maintenance

Page 33

MAINTENANCE

Below you will find some general maintenance instructions. If you have more questions, contact your servicing dealer.

Weekly maintenance

Daily maintenance

1. Check that the AV

elements are not soft or

torn.

1

2

1. Check the throttle trigger

for smooth operation. If

any binding occurs, or if

engine fails to return to

idle, the saw should be

taken to your dealer,

before it is used again.

Also, be sure that the

trigger cannot be pulled

until the throttle trigger

lockout is depressed.

2. Clean the chain brake

and check its function

according to the

instructions. Make sure

that the chain catcher is

undamaged. Otherwise

replace it immediately.

3. Clean or replace the air

filter as necessary. Check

for damage or holes.

4. The bar should be turned

daily for more even wear.

1

2

3

2.

Lubricate the clutch drum

 

bearing.

3.

File off burrs, if any, on

 

the sides of the bar.

4.

Clean the spark plug and

 

check the gap.

 

The correct gap is 0,5 mm

 

(0,020 inch).

5.

Check the starter and the

 

recoil spring. Clean the

 

fins on the flywheel.

6.

Clean the cooling fins on

 

the cylinder.

7.

Clean or change the

 

screen in the muffler.

8.

Clean the carburetor body

 

and air box.

3

4

5

6

7

0,5 mm

Check the lubrication hole

in the bar, to be sure it is

not clogged. Clean the

bar groove, if the bar has

a sprocket tip, this should

be lubricated.

5. Check the function of the

oiler to be sure the bar

and chain receive proper

4

5

6

8

Monthly maintenance

 

lubrication.

6.

Sharpen the chain and

 

check its tension and

 

condition. Check the drive

 

sprocket for wear.

 

Replace if necessary.

7.

Check the starter and

 

starter cord for wear or

 

damage. Clean the air

 

intake slots on the starter

 

housing.

8.

Check for any loose nuts

 

and screws and retighten

 

if necessary.

9.

Test the stop switch to be

 

sure it shuts off the

 

engine.

7

8

9

1.Check the brake band on the chain brake for wear.

2.Check the clutch centre, clutch drum and clutch spring for wear.

3.Clean the outside of the carburetor.

4.Change the fuel filter.

5.Clean the inside of the fuel tank.

6.Clean the inside of the oil tank.

7.Check all cables and connections.

8.Change the spark plug.

9.Change the air filter.

1

 

2

 

3

 

4

 

5

 

6

 

7

 

8

0,5 mm

Long-term storage

Empty the fuel/oil tanks in a well ventilated area. Store the fuel in approved cans in a safe place. Fit the bar guard.

Clean the machine. See weekly maintenance.

9

English – 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents EPA II 350 Symbols KEY to SymbolsEPA ContentsChain SAW Safety Equipment Safety Instructions3a Starting Chain brake and front hand guardThrottle lock Chain catcherRight hand guard Stop switch Vibration damping systemMuffler Checking the front hand guard Checking brake band wearChecking the inertia brake release Checking the brake triggerThrottle lock 5 basic rules Cutting EquipmentBar Cutting equipment designed to minimise kickbackSaw chain Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth Risk of kickback is increased with a badly sharpened chainGeneral advice on setting raker clearance Setting the raker clearanceTensioning the chain Chain oil Lubricating cutting equipmentFilling with chain oil Never use waste oilChecking chain lubrication Needle bearing maintenanceChecking wear on cutting equipment Lubricating the bar tip sprocketWhat is kickback? HOW to Avoid KickbackGeneral rules Do not let go of the handlesNever use the saw one- handed General Safety Precautions Min m10 ft General Working Instructions Basic safety rulesGeneral Basic cutting techniqueTerms CuttingSafe distance Tree felling techniqueLimbing Felling directionFelling Clearing the trunk and preparing your retreatFreeing a tree that has fallen badly = high accident risk General adviceCutting the trunk into logs Freeing a Trapped treeWhat is what? What is WHAT?Mounting guide bar and chain Assembly340 345/350Fuelmix Fuel HandlingFuelling Min 3 m10ft Start and stop Start and StopStart StopCarburetor MaintenanceStarter device Starter device assemblyChanging a broken or worn starter cord Tensioning the recoil springAdjustment of the oil pump Needle bearing maintenanceAir filter MufflerTemperature -5C or colder Centrifugal cleaning Air InjectionCooling system Winter useWeekly maintenance Daily maintenance Monthly maintenanceLong-term storage 340 345 350 Technical DataYour Warranty Rights Obligations Emission Control Warranty Statement2002W49 114 01

345 EPA II, 340 EPA II, 345 EPA II, 350 EPAI specifications

Husqvarna, a renowned leader in the outdoor power equipment industry, offers a range of chainsaws designed for various needs and applications. Among their impressive lineup, the Husqvarna 340 EPA II, 345 EPA II, and 350 EPA I chainsaws stand out for their robust performance and innovative features.

The Husqvarna 340 EPA II is designed to cater to both homeowners and professionals. Its lightweight design, weighing only 4.9 kg, ensures maneuverability without sacrificing power. The chainsaw is powered by a 40.9 cc engine, providing ample power for tasks such as pruning, cutting firewood, and light felling. One key feature is its X-Torq engine technology, which optimizes fuel efficiency while reducing harmful emissions, ensuring compliance with environmental regulations. The ergonomic handle and low vibration design enhance user comfort during extended use.

Next, the Husqvarna 345 EPA II takes the essentials of the 340 and amps them up. With a slightly larger 45.7 cc engine, this chainsaw offers increased cutting power, making it ideal for homeowners who require more robust performance. The chainsaw features an automatic oiler for consistent lubrication of the chain, which prolongs the lifespan of the chain and bar. Additionally, the 345 EPA II incorporates an easy start system, allowing users to start the machine with minimal effort, making it a practical choice for all skill levels.

Finally, the Husqvarna 350 EPA I is built for seasoned professionals who demand high performance. Equipped with a powerful 50.1 cc engine, it delivers exhilarating cutting speeds for demanding applications. The chainsaw features advanced ignition systems that ensure quick starts and reliable performance in various conditions. One of the standout characteristics of the 350 EPA I is its Air Injection technology, which centrifugal forces remove dust and debris from the air intake. This filtration system helps maintain engine efficiency and prolongs service intervals.

All three models are equipped with Husqvarna's signature features, including easy access to air filters for maintenance and a chain brake for added safety. Their durable construction and advanced ergonomics make them versatile tools, whether for occasional use in residential settings or for tackling rigorous tasks in commercial environments. With a commitment to innovation and sustainability, Husqvarna's EPA II chainsaws continue to set the standard for performance and reliability in the outdoor power equipment industry.
Top Page Image Contents