Husqvarna 346XP EPA II manual Air Injection centrifugal cleaning, Winter use, Heated handles

Page 35

MAINTENANCE

”Air Injection” centrifugal cleaning

Centrifugal cleaning means the following: All air to the carburetor passes through the starter. Dirt and dust is pushed out by the cooling fan.

IMPORTANT! In order to maintain operation of the centrifugal cleaning system it must be regularly maintained. Clean the air intake to the starter, the fins on the flywheel, the space around the flywheel, inlet pipe and carburetor compartment.

Winter use

Running problems can occur when using the machine in the cold and snowy conditions caused by:

•Too low engine temperature.

•Icing of the air filter and carburetor. Special measures are therefore often required:

•Partly mask the air inlet on the starter to increase the working temperature of the engine.

•Preheat the intake air to the carburetor by using the heat from the cylinder.

Temperature 0°C (32°F) or colder:

The cylinder cover is designed so it can be adjusted for running in cold weather. Twist the winter flap so that preheated air from the cylinder can pass into the carburetor space preventing icing of the air filter, etc.

For temperatures below -5°C (23°F) and/or in snow conditions there is also:

•a special cover (A) for the starter housing

•a winter plug (B) for the air nozzle that is fitted as shown.

These reduce the flow of cooling air and prevent large amounts of snow from being sucked into the carburetor space.

CAUTION! When the winter plug is fitted the winter flap must be open!

IMPORTANT! If the temperature rises above -5°C (23°F) or 0°C (32°F) respectively the machine MUST be restored to its normal set-up. Otherwise there is a risk of overheating, which can cause severe engine damage.

Heated handles

(346XPG, 353G)

On models with the designation XPG/G, the front as well as the rear handle are equipped with electric heating coils. These are fed with electrical current from an integrated generator in the chain saw.

When the switch is pushed downwards, the heat is switched on. When the switch is pushed upwards, the heat is switched off.

Electrical carburetor heating

(346XPG, 353G)

On models with the designation CARBURETOR HEATING there is an electrically heated carburetor. Electrically powered heating prevents ice formation in the carburetor. A thermostat regulates the heating so that the carburetor always has the right working temperature.

English – 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Operator’s manual 346XP EPA II 353 EPA You will find the following labels on your chain saw KEY to SymbolsSymbols on the machine Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Muffler Stop switchCutting equipment Vibration damping systemChain General rulesCutting equipment designed to reduce kickback BarInstructions considerably increases the risk of kickback Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Sharpening cutting teethTensioning the chain General advice on adjusting depth gauge settingAdjustment of depth gauge setting If the depth gauge setting is too largeChecking chain lubrication Lubricating cutting equipmentChain oil Filling with chain oilChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Fitting the bar and chain AssemblyFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueGeneral Cutting LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut FellingDirectional cuts Cutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment High speed jet H Correctly adjusted carburetorThrottle lockout Changing a broken or worn starter cord MufflerStarter Changing a broken recoil spring Air filterSpark plug Tensioning the recoil springNeedle bearing lubrication Adjustment of the oil pumpWhen making adjustments Lubricating the bar tip sprocketHeated handles Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Bar and chain combinationsSaw chain filing and file gauges 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage ´z+RA¶5t¨ Page 1150339-95 ´z+RA¶5t¨ ´z+RA¶5t¨
Top Page Image Contents