Husqvarna 346XP EPA II manual Directional cuts, Felling cut

Page 26

WORKING TECHNIQUES

Felling

WARNING! Unless you have special training

!we advise you not to fell trees with a diameter larger than the bar length of your saw!

Felling is done using three cuts. First you make the directional cuts, which consist of the top cut and the bottom cut, then you finish with the felling cut. By placing these cuts correctly you can control the felling direction very accurately.

Directional cuts

To make the directional cuts you begin with the top cut. Stand to the right of the tree and cut on the pull stroke.

Next make the bottom cut so that it finishes exactly at the end of the top cut.

The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°.

The line where the two cuts meet is called the directional cut line. This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction.

Felling cut

The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut on the pull stroke.

Make the felling cut about 1.5-2 inches (3-5 cm) above the bottom directional cut.

Finish the felling cut parallel with the directional cut line so that the distance between them is at least 1/10 of the trunk diameter. The uncut section of the trunk is called the felling hinge.

The felling hinge controls the direction that the tree falls in.

All control over the felling direction is lost if the felling hinge is too narrow or non-existent, or if the directional cuts and felling cut are badly placed.

When the felling cut and directional cut are complete the tree should start to fall by itself or with the aid of a felling wedge or breaking bar.

26 – English

Image 26
Contents Operator’s manual 346XP EPA II 353 EPA Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping system Stop switchCutting equipment MufflerBar General rulesCutting equipment designed to reduce kickback ChainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Instructions considerably increases the risk of kickbackIf the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainFilling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Terms Basic cutting techniqueGeneral Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling cut FellingDirectional cuts Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Correctly adjusted carburetor High speed jet HThrottle lockout Changing a broken or worn starter cord MufflerStarter Tensioning the recoil spring Air filterSpark plug Changing a broken recoil springLubricating the bar tip sprocket Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+RA¶5t¨ Page 1150339-95 ´z+RA¶5t¨ ´z+RA¶5t¨