Husqvarna 254XP, 257, 262XP manual Weekly maintenance Daily maintenance, Monthly maintenance

Page 33

MAINTENANCE

Below you will find some general maintenance instructions. If you have more questions, contact your servicing dealer.

Weekly maintenance

Daily maintenance

1. Check that the AV

elements are not soft or

torn.

1

1. Check the throttle trigger

for smooth operation. If

any binding occurs, or if

engine fails to return to

idle, the saw should be

taken to your dealer,

before it is used again.

Also, be sure that the

trigger cannot be pulled

until the throttle trigger

lockout is depressed.

2. Clean the chain brake

and check its function

according to the

instructions. Make sure

that the chain catcher is

undamaged. Otherwise

replace it immediately.

3. Clean or replace the air

filter as necessary. Check

for damage or holes.

4. The bar should be turned

daily for more even wear.

Check the lubrication hole

in the bar, to be sure it is

not clogged. Clean the

bar groove, if the bar has

a sprocket tip, this should

be lubricated.

5. Check the function of the

oiler to be sure the bar

1

2

3

4

5

6

2.

Lubricate the clutch drum

 

bearing.

3.

File off burrs, if any, on

 

the sides of the bar.

4.

Clean the spark plug and

 

check the gap.

 

The correct gap is 0.5 mm

 

(.020 inch).

5.

Check the starter and the

 

recoil spring. Clean the

 

fins on the flywheel.

6.

Clean the cooling fins on

 

the cylinder.

7.

Clean or change the

 

screen in the muffler.

8.

Clean the carburettor

 

body and air box.

2

3

4

5

6

7

8

0,5 mm

and chain receive proper

lubrication.

Monthly maintenance

6.

Sharpen the chain and

 

check its tension and

 

condition. Check the drive

 

sprocket for wear.

 

Replace if necessary.

7.

Check the starter and

 

starter cord for wear or

 

damage. Clean the air

 

intake slots on the starter

 

housing.

8.

Check for any loose nuts

 

and screws and retighten

 

if necessary.

9.

Test the stop switch to be

 

sure it shuts off the

 

engine.

7

8

9

1.Check the brake band on the chain brake for wear.

2.Check the clutch centre, clutch drum and clutch spring for wear.

3.Clean the outside of the carburettor.

4.Check the fuel filter. Change if necessary.

5.Flush the inside off the fuel tank with gasoline.

6.Flush the inside of the oil tank with gasoline.

7.Check all cables and connections.

1

2

3

4

5

6

7

English – 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents 101 88 254XP/257/262XPKEY to Symbols Symbols on the chain sawSymbols in the operator’s manual Contents Safety Instructions Chain SAW Safety EquipmentPersonal Protective Equipment Chain brake and front hand guard Throttle lock Chain catcherRight hand guard Stop switch Vibration damping systemMuffler Checking the front hand guard Checking brake band wearChecking the automatic brake Checking the brake triggerThrottle lock 5 basic rules Cutting EquipmentBar Cutting equipment designed to minimise kickbackSaw chain Some terms that describe the bar and chainSharpening your chain and adjusting raker clearance General information on sharpening cutting teethSharpening cutting teeth General advice on setting raker clearance Setting the raker clearanceTensioning the chain Chain oil Lubricating cutting equipmentFilling with chain oil Never use waste oilLubricating the clutch drum bearing Checking chain lubricationChecking wear on cutting equipment Lubricating the bar tip sprocketWhat is kickback? HOW to Avoid KickbackGeneral rules Do not let go of the handlesNever use the saw one- handed General Safety Precautions Min m10 ft General Working Instructions Basic safety rulesGeneral Basic cutting techniqueTerms CuttingSafe distance Tree felling techniqueLimbing Felling directionFelling Clearing the trunk and preparing your retreatFreeing a tree that has fallen badly = high accident risk General adviceCutting the trunk into logs Freeing a Trapped treeWhat is WHAT? Assembly Mounting guide bar and chainFitting a spike bumper Fuelmix Fuel HandlingFuelling Min 3 m10ft Start Start and StopCold engine Warm engineCarburettor MaintenanceStarter device Starter device assemblyChanging a broken or worn starter cord Tensioning the recoil springNeedle bearing maintenance Adjustment of the oil pumpAir filter Spark plugCooling system Centrifugal cleaning Air InjectionWinter use Heated handlesMonthly maintenance Weekly maintenance Daily maintenanceTechnical Data 254XP 257Bar and chain combinations Fuel and lubrication 262XP

254XP, 257, 262XP, 354XP, 257, 262XP specifications

Husqvarna is a well-respected name in the world of outdoor power equipment, especially when it comes to chainsaws. Among its lineup, the models 254XP, 257, 262XP, and 354XP stand out for their robust performance and innovative technologies, catering to both professional and amateur users.

The Husqvarna 254XP is known for its high power-to-weight ratio, making it a favorite among professionals who require portability without sacrificing performance. It features a 2.3 kW engine, providing ample power for a variety of cutting tasks. The chainsaw is equipped with a robust air injection system that removes larger debris before it reaches the air filter, helping to maintain engine performance and extend service intervals.

Similar to the 254XP, the Husqvarna 257 offers strong performance, but with enhancements tailored for even greater efficiency. It boasts an efficient combustion system, ensuring lower fuel consumption and reduced emissions, making it environmentally friendly. Another standout feature is the LowVib technology, which minimizes vibrations, making it easier for operators to work for extended periods without fatigue.

The Husqvarna 262XP takes a step further in terms of power and efficiency, featuring a 3.2 kW engine. This model is designed for heavy-duty tasks and is appreciated in the logging industry. Its advanced ignition system ensures quick starts and stable operation, even in challenging conditions. The X-Torq engine technology reduces fuel consumption and emissions, making it a green choice for professionals.

The 354XP is engineered for those who require a balance of power and weight. With a cutting capacity that satisfies both casual users and professionals, it delivers 2.9 kW of power. The chainsaw’s design incorporates features like the automatic chain lubrication system, ensuring optimal oil flow to the bar and chain, which prolongs their lifespan.

In terms of ergonomics, all these models come with comfort-grip handles and adjustable oil pumps, allowing for ease of use and control during operation. Their starting mechanisms are user-friendly, often featuring a decompression valve for easier pull starts.

These Husqvarna models exemplify the brand's commitment to merging power, efficiency, and user comfort. Whether tackling small projects or heavy-duty logging, the 254XP, 257, 262XP, and 354XP offer dependable solutions that meet the demands of today’s users.
Top Page Image Contents