Husqvarna 354XP, 257, 262XP manual Clearing the trunk and preparing your retreat, Felling

Page 22

SAFETY INSTRUCTIONS

C Clearing the trunk and preparing your retreat

Remove any branches that are in the way. To do this it is best to work from the top down and keep the trunk between you and the chain saw. Never limb above shoulder height.

Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall. Your path of retreat should be roughly 135 degrees behind the intended felling direction.

D Felling

Felling is done using three cuts. First you make the DIRECTIONAL CUTS, which consist of the TOP CUT and the BOTTOM CUT; followed by the FELLING CUT. By placing these cuts correctly you can control the felling direction very accurately.

DIRECTIONAL CUT

To make the DIRECTIONAL CUT you begin with the TOP CUT. Stand to the right of the tree and cut downwards at an angle.

Next make the BOTTOM CUT so that it finishes at the end of the TOP CUT.

The directional cut should run 1/4 of the diameter through the trunk and the angle between the TOP CUT and BOTTOM CUT should be 45°.

The line where the two cuts meet is called the

DIRECTIONAL CUT LINE. This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction.

FELLING CUT

The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut with the bottom edge of the bar.

Make the FELLING CUT about 3-5 cm (1.5-2 inches) above the flat section of the

DIRECTIONAL CUT.

Set the spike bumper in behind the breaking strip (if one is fitted).Use full throttle and bring the bar and chain slowly into the tree. Make sure the tree does not start to move in the opposite direction to your intended felling direction. Drive a WEDGE or BREAKING BAR into the cut as soon as it is deep enough.

Finish the FELLING CUT parallel with the DIRECTIONAL CUT LINE so that the distance between them is at least at least 1/10 of the trunk diameter. The uncut section of the trunk is called the BREAKING STRIP.

The BREAKING STRIP act as hinges that control the felling direction of the falling tree.

All control over the felling direction is lost if the BREA- KING STRIP is too narrow or if the directional cut and felling cut are badly placed.

When the felling cut and directional cut are complete the tree should start to fall under its own weight or with the aid of a FELLING WEDGE or BREAKING BAR.

22 – English

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 254XP/257/262XP 101 88Symbols on the chain saw KEY to SymbolsSymbols in the operator’s manual Contents Chain SAW Safety Equipment Safety InstructionsPersonal Protective Equipment Chain brake and front hand guard Chain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking the automatic brake Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth Setting the raker clearance General advice on setting raker clearanceTensioning the chain Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilChecking wear on cutting equipment Checking chain lubricationLubricating the clutch drum bearing Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Do not let go of the handles General rulesNever use the saw one- handed Min m General Safety Precautions10 ft Basic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? Mounting guide bar and chain AssemblyFitting a spike bumper Fuel Handling FuelmixMin 3 m Fuelling10ft Cold engine Start and StopStart Warm engineMaintenance CarburettorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springAir filter Adjustment of the oil pumpNeedle bearing maintenance Spark plugWinter use Centrifugal cleaning Air InjectionCooling system Heated handlesWeekly maintenance Daily maintenance Monthly maintenance254XP 257 Technical DataBar and chain combinations 262XP Fuel and lubrication

254XP, 257, 262XP, 354XP, 257, 262XP specifications

Husqvarna is a well-respected name in the world of outdoor power equipment, especially when it comes to chainsaws. Among its lineup, the models 254XP, 257, 262XP, and 354XP stand out for their robust performance and innovative technologies, catering to both professional and amateur users.

The Husqvarna 254XP is known for its high power-to-weight ratio, making it a favorite among professionals who require portability without sacrificing performance. It features a 2.3 kW engine, providing ample power for a variety of cutting tasks. The chainsaw is equipped with a robust air injection system that removes larger debris before it reaches the air filter, helping to maintain engine performance and extend service intervals.

Similar to the 254XP, the Husqvarna 257 offers strong performance, but with enhancements tailored for even greater efficiency. It boasts an efficient combustion system, ensuring lower fuel consumption and reduced emissions, making it environmentally friendly. Another standout feature is the LowVib technology, which minimizes vibrations, making it easier for operators to work for extended periods without fatigue.

The Husqvarna 262XP takes a step further in terms of power and efficiency, featuring a 3.2 kW engine. This model is designed for heavy-duty tasks and is appreciated in the logging industry. Its advanced ignition system ensures quick starts and stable operation, even in challenging conditions. The X-Torq engine technology reduces fuel consumption and emissions, making it a green choice for professionals.

The 354XP is engineered for those who require a balance of power and weight. With a cutting capacity that satisfies both casual users and professionals, it delivers 2.9 kW of power. The chainsaw’s design incorporates features like the automatic chain lubrication system, ensuring optimal oil flow to the bar and chain, which prolongs their lifespan.

In terms of ergonomics, all these models come with comfort-grip handles and adjustable oil pumps, allowing for ease of use and control during operation. Their starting mechanisms are user-friendly, often featuring a decompression valve for easier pull starts.

These Husqvarna models exemplify the brand's commitment to merging power, efficiency, and user comfort. Whether tackling small projects or heavy-duty logging, the 254XP, 257, 262XP, and 354XP offer dependable solutions that meet the demands of today’s users.
Top Page Image Contents