Husqvarna 354XP, 257, 262XP, 254XP, 257, 262XP Basic cutting technique, General, Terms, Cutting

Page 20

SAFETY INSTRUCTIONS

2 Basic cutting technique

General

•Always use full throttle when cutting!

•Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load can lead to serious engine damage).

•Cutting from above = Cutting on the pull stroke.

•Cutting from below = Cutting on the push stroke.

See the section on ”How to avoid kickback” to find out why cutting on the push stroke increases the risk of kickback.

Terms:

Cutting

=

General term for cutting through wood.

Limbing

=

Cutting limbs off a felled tree.

Splitting

=

When the object you are cutting breaks off

 

 

before the cut is complete.

There are five important factors you should consider before making a cut:

1Make sure the bar will not jam in the cut.

2Make sure the log will not split.

3 Make sure the chain will not strike the ground or any other object during or after cutting.

4Is there a risk of kick- back?

5Do the conditions and surrounding terrain affect your safety when working?

Two factors decide whether the chain will jam or the log will split. The first is how the log is supported and the second is whether it is in tension.

In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom of the log. You need to support the log so that it will not trap the chain or split during cutting.

!If the chain jams in the cut:

STOP THE ENGINE! Don’t try to pull the saw free. If you do you may damage the chain when the saw suddenly breaks free. Use a lever to open up the cut and free the bar.

The following instructions describe how to handle most types of situation that you will be faced with when using a chain saw.

Cutting

1 The log is lying on the ground. There is little risk of the chain jamming or the log splitting. However there is a risk that the chain will touch the ground when you finish the cut.

Cut all the way through the log from above. Try not to touch the ground as you finish the cut. Maintain full throttle but be prepared in case the chain snatches.

A If it is possible to turn the log you should stop cutting about 2/3 of the way through.

B Turn the log and finish the cut from the opposite side.

20 – English

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 254XP/257/262XP 101 88Symbols in the operator’s manual KEY to SymbolsSymbols on the chain saw Contents Personal Protective Equipment Safety InstructionsChain SAW Safety Equipment Chain brake and front hand guard Right hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking brake band wear Checking the front hand guardChecking the automatic brake Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesCutting equipment designed to minimise kickback BarSaw chain Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Tensioning the chain General advice on setting raker clearanceSetting the raker clearance Lubricating cutting equipment Chain oilFilling with chain oil Never use waste oilChecking chain lubrication Lubricating the clutch drum bearingChecking wear on cutting equipment Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Never use the saw one- handed General rulesDo not let go of the handles 10 ft General Safety PrecautionsMin m Basic safety rules General Working InstructionsBasic cutting technique GeneralTerms CuttingTree felling technique Safe distanceLimbing Felling directionClearing the trunk and preparing your retreat FellingGeneral advice Freeing a tree that has fallen badly = high accident riskCutting the trunk into logs Freeing a Trapped treeWhat is WHAT? Fitting a spike bumper AssemblyMounting guide bar and chain Fuel Handling Fuelmix10ft FuellingMin 3 m Start and Stop StartCold engine Warm engineMaintenance CarburettorStarter device assembly Starter deviceChanging a broken or worn starter cord Tensioning the recoil springAdjustment of the oil pump Needle bearing maintenanceAir filter Spark plugCentrifugal cleaning Air Injection Cooling systemWinter use Heated handlesWeekly maintenance Daily maintenance Monthly maintenanceBar and chain combinations Technical Data254XP 257 262XP Fuel and lubrication

254XP, 257, 262XP, 354XP, 257, 262XP specifications

Husqvarna is a well-respected name in the world of outdoor power equipment, especially when it comes to chainsaws. Among its lineup, the models 254XP, 257, 262XP, and 354XP stand out for their robust performance and innovative technologies, catering to both professional and amateur users.

The Husqvarna 254XP is known for its high power-to-weight ratio, making it a favorite among professionals who require portability without sacrificing performance. It features a 2.3 kW engine, providing ample power for a variety of cutting tasks. The chainsaw is equipped with a robust air injection system that removes larger debris before it reaches the air filter, helping to maintain engine performance and extend service intervals.

Similar to the 254XP, the Husqvarna 257 offers strong performance, but with enhancements tailored for even greater efficiency. It boasts an efficient combustion system, ensuring lower fuel consumption and reduced emissions, making it environmentally friendly. Another standout feature is the LowVib technology, which minimizes vibrations, making it easier for operators to work for extended periods without fatigue.

The Husqvarna 262XP takes a step further in terms of power and efficiency, featuring a 3.2 kW engine. This model is designed for heavy-duty tasks and is appreciated in the logging industry. Its advanced ignition system ensures quick starts and stable operation, even in challenging conditions. The X-Torq engine technology reduces fuel consumption and emissions, making it a green choice for professionals.

The 354XP is engineered for those who require a balance of power and weight. With a cutting capacity that satisfies both casual users and professionals, it delivers 2.9 kW of power. The chainsaw’s design incorporates features like the automatic chain lubrication system, ensuring optimal oil flow to the bar and chain, which prolongs their lifespan.

In terms of ergonomics, all these models come with comfort-grip handles and adjustable oil pumps, allowing for ease of use and control during operation. Their starting mechanisms are user-friendly, often featuring a decompression valve for easier pull starts.

These Husqvarna models exemplify the brand's commitment to merging power, efficiency, and user comfort. Whether tackling small projects or heavy-duty logging, the 254XP, 257, 262XP, and 354XP offer dependable solutions that meet the demands of today’s users.
Top Page Image Contents