Husqvarna YTH2042TD manual Tractor, Brake Operation, Tires, Blade Care, Battery

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved sur- face,thenbrakemustbeserviced.(See“TOCHECKBRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See PSI on tires).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

 

02828

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be sharp. Replace

 

worn, bent or damaged blades.

15

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 13)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

MANDREL ASSEMBLY

 

BLADE

BLADE BOLT

STAR

(SPECIAL)

CENTER HOLE

Fig. 13

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual).

Page 14 Page 16
Image 15
Page 14 Page 16
Contents YTH2042TD II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents Unpack Carton AssemblyUnassembled Parts To Remove Tractor from CartonCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Cruise Control Lever Used to set forward Know Your TractorHOW to USE Your Tractor To Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig System CharacteristicsTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Reverse Operation System ROSAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Schedule MaintenanceMaintenance General RecommendationsTires BatteryTractor Brake OperationEngine Cleaning Service and Adjustments To Install Mower See FigsTo Remove Mower See Fig Service and Adjustments To Level Mower To Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Check Brake To Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Engine OIL StorageOther Fuel SystemTroubleshooting Points Engine continues Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation02.24.10 CL

YTH2042TD specifications

The Husqvarna YTH2042TD is a robust and versatile garden tractor designed to make mowing large areas efficient and enjoyable. This model combines power, performance, and comfort, making it an excellent choice for homeowners with extensive lawns.

One of the standout features of the YTH2042TD is its powerful 20 HP Kohler engine. This reliable engine delivers consistent performance, allowing the mower to tackle tough grass and uneven terrain with ease. The hydrostatic transmission provides a smooth and effortless driving experience, enabling users to adjust speed seamlessly without the need for gear shifting.

The cutting deck of the YTH2042TD measures 42 inches, optimized for efficient mowing. With the ability to adjust the cutting height between 1 to 4 inches, users can choose the ideal trim for their lawn, promoting healthy grass growth. The mower also utilizes a clear-cutting system that ensures an even and precise cut every time.

Incorporating innovative technologies, the Husqvarna YTH2042TD features an easy-to-use deck lift system. This allows users to change the cutting height quickly and effortlessly from the operator’s seat. Additionally, an integrated cruise control feature lets users maintain a steady speed for a more comfortable mowing experience over large areas.

Another key characteristic of the YTH2042TD is its ergonomic design. The high-back seat provides excellent support, allowing users to remain comfortable during longer mowing sessions. The instrument panel is also conveniently located for easy access to controls, enhancing the overall usability of the tractor.

The Husqvarna YTH2042TD stands out for its durability and long-lasting construction. Built with high-quality materials, this mower is engineered to withstand the rigors of regular use, ensuring that it remains operational for years to come. Its robust frame and sturdy build give users confidence that it can handle demanding tasks.

Safety features have also been thoughtfully integrated into the design. The automatic blade engagement system is a standout, ensuring that the mower blades engage smoothly while minimizing the risk of accidents. An ignition switch with a safety interlock prevents the engine from starting unless the mower is in gear.

In conclusion, the Husqvarna YTH2042TD is a feature-rich garden tractor that combines power, comfort, and advanced technology. With its powerful engine, adjustable cutting deck, and ergonomic design, it provides an exceptional mowing experience, making it an ideal choice for those looking to maintain their lawns with ease and efficiency.
Top Page Image Contents