Husqvarna YTH2042 TWIN owner manual Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 21

SERVICE AND ADJUSTMENTS

B

G

H

A

C	J
	J
D
E
F

02953 electric

FIG. 27

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 28

22

Image 21

Contents YTH2042 Twin Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Operate MowerBefore Starting the Engine Service REMINDER/HOUR MeterTo Operate on Hills Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBrake Operation TiresEngine IN-LINE Fuel Filter See Fig CleaningService and Adjustments To Level Mower To Replace Mower Blade Drive Belt See Fig Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Check Brake To Remove Mower See Fig To Install Mower See FigReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Decals Wheels and TiresKEY Part Description Tractor Model NO. YTH2042 Twin 96041005400, Product no 41 SchematicElectrical KEY Part NO. NO. Description Chassis KEY Part Description Drive 17 532 41 36-78 Spring, Brake Steering Assembly Engine Spark Arrester KITSeat Assembly Mower Lift Mower Deck Tractor Model NO. YTH2042 Twin 96041005400, Product no 41 Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 41 00-15 Rev 05.21.07 CL