Husqvarna YTH20K46 To Start Engine See Fig, Purge Transmission, Automatic Transmission Warm UP

Page 12

OPERATION

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•The attachments can also be used during the engine warm-up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the en- gine is running, move throttle control to slow position. Disengage parking brake

CAUTION: At any time, during step 4, there may be movement of the drive wheels.

•Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five

(5) seconds and release pedal. Repeat this procedure three (3) times.

•Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

•Drive tractor forward for approximately five feet then backwards for five feet. Repeat this driving procedure three times.

Your transmission is now purged and now ready for normal operation.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents YTH20K46 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Check BatteryUnassembled Parts To Remove Tractor from CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigSystem Characteristics To Operate MowerService REMINDER/HOUR Meter Before Starting the EngineTo Operate on Hills Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBrake Operation TiresEngine Cleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH20K46 96043003300, Product no 43Electrical KEY Part NO. NO. Description Chassis Tractor - Model Number YTH20K46 96043003300, Product no 43 Drive KEY Part Description Steering Assembly 30!2+ª!22%34%2ª+4 EngineSeat Assembly Decals Wheels and TiresMower Deck Tractor - Model Number YTH20K46 96043003300, Product no 43 Mower Lift Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 04-50 11.14.06 TH
Related manuals
Manual 44 pages 37.67 Kb

YTH20K46 specifications

The Husqvarna YTH20K46 is a premier riding lawn mower designed for homeowners who seek efficiency, durability, and ease of use while maintaining their lawn. This versatile machine combines power and performance with advanced technologies, making it a reliable choice for various landscaping tasks.

One of the standout features of the YTH20K46 is its robust 20 HP Kohler engine, which provides ample power to handle even the toughest mowing conditions. The engine's design focuses on durability and efficiency, ensuring that users can tackle their larger lawns with ease and minimal maintenance. This riding mower is equipped with a 46-inch cutting deck, allowing for wide mowing swathes that significantly reduce mowing time while delivering an exceptional cut quality.

The mower employs an innovative automatic transmission system, which simplifies operation with a pedal-controlled system. This feature allows the operator to seamlessly adjust speed without the need for manual gear shifting, providing greater comfort during operation. The intuitive controls ensure tasks can be completed efficiently, even for less experienced users.

Another significant aspect of the YTH20K46 is its adjustable cutting height feature. Users can easily select from various cutting heights to achieve the desired lawn finish, ranging from 1.5 to 4 inches. This versatility is essential for adapting to different grass types and seasonal changes.

For added convenience, the Husqvarna YTH20K46 incorporates maintenance-friendly technology, such as an easy-access oil filter and a removable deck for quick blade sharpening or replacement. This attention to maintenance ensures that users can keep their mower in top working condition with minimal effort.

Ergonomics is also a key consideration in the design of this mower. The comfortable high-back seat provides excellent support during long mowing sessions, while the ergonomic steering wheel enhances maneuverability. Additionally, the mower features a built-in hour meter to keep track of maintenance intervals.

In summary, the Husqvarna YTH20K46 is an impressive riding mower that combines powerful performance, user-friendly features, and advanced technology. Its reliability and efficiency make it an ideal choice for homeowners looking to maintain their lawns effortlessly while achieving professional-quality results. With its durable construction and robust capabilities, the YTH20K46 stands out as a top contender in the riding mower category.
Top Page Image Contents