Husqvarna 336 EPA I manual Sharpening your chain and adjusting depth gauge setting

Page 12

GENERAL SAFETY PRECAUTIONS

Chain

•Chain pitch (inches)

•Drive link width (mm/inches)

•Number of drive links.

Sharpening your chain and adjusting depth gauge setting

General information on sharpening cutting teeth

•Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the cuttings will be very small. If the chain is very blunt it will not produce any cuttings at all. Wood powder would be the only result.

•A sharp chain eats its way through the wood and produces long, thick cuttings.

•The cutting part of the chain is called the cutting link and this consists of a cutting tooth (A) and the raker lip (B).The cutting depth is determined by the difference in height between the two.

When you sharpen a cutting tooth there are four important factors to remember.

1 Filing angle

2 Cutting angle

3File position

4Round ﬁle diameter

It is very difﬁcult to sharpen a chain correctly without the right equipment. We recommend that you use our ﬁle gauge. This will help you obtain the maximum kickback reduction and cutting performance from your chain.

See instructions under the heading Technical data for information about sharpening your chain.

WARNING! Departure from the sharpening

!instructions considerably increases the risk of kickback.

Sharpening cutting teeth

To sharpen cutting teeth you will need a round ﬁle and a ﬁle gauge. See instructions under the heading Technical data for information on the size of ﬁle and gauge that are recommended for the chain ﬁtted to your chain saw.

•Check that the chain is correctly tensioned. A slack chain will move sideways, making it more difﬁcult to sharpen correctly.

•Always ﬁle cutting teeth from the inside face. Reduce the pressure on the return stroke. File all the teeth on one side ﬁrst, then turn the chain saw and ﬁle the teeth on the other side.

12 – English

Image 12

Contents Operator’s manual 336 EPA KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Stop switch Cutting equipmentVibration damping system MufﬂerGeneral rules Cutting equipment designed to minimise kickbackBar ChainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethSharpening cutting teeth General advice on adjusting depth gauge setting Adjustment of depth gauge settingTensioning the chain 336Lubricating cutting equipment 339XPChain oil Filling with chain oilChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainFuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique GeneralTerms Limbing CuttingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatFelling Directional cutsGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor High speed jet HChecking brake band wear Checking the front hand guardChecking the brake trigger Mufﬂer StarterChanging a broken or worn starter cord Air ﬁlter Tensioning the recoil springChanging a broken recoil spring Fitting the starterAdjustment of the oil pump Spark plugLubricating the bar tip sprocket Cooling systemMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations, model Saw chain ﬁling and ﬁle gaugesFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions1150239-95 ´z+R7¶5B¨ ´z+R7¶5B¨