Husqvarna 336 EPA I Spark plug, Lubricating the bar tip sprocket, Adjustment of the oil pump

Page 34

MAINTENANCE

Spark plug

The spark plug condition is inﬂuenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air ﬁlter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difﬁculties.

If the machine is low on power, difﬁcult to start or runs poorly at idle speed: always check the spark plug ﬁrst before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm (0,020"). The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is ﬁtted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory set to 1 turn open. Turning the screw clockwise will reduce the oil ﬂow and turning the screw anti-clockwise will increase the oil ﬂow. CAUTION! Max. 1 1/2 turns.

WARNING! The engine must be stopped

!when making adjustments.

Cooling system

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

1Air intake on the starter.

2Air guide plate.

3Fins on the ﬂywheel.

4Cooling ﬁns on the cylinder.

5Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder.

34 – English

Image 34

Contents Operator’s manual 336 EPA Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockoutRight hand guard Vibration damping system Stop switchCutting equipment MufﬂerBar General rulesCutting equipment designed to minimise kickback ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth Tensioning the chain General advice on adjusting depth gauge settingAdjustment of depth gauge setting 336Chain oil Lubricating cutting equipment339XP Filling with chain oilNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules General Basic cutting techniqueTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatFelling Directional cutsFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking brake band wear Correctly adjusted carburetorHigh speed jet H Checking the front hand guardChecking the brake trigger Starter MufﬂerChanging a broken or worn starter cord Changing a broken recoil spring Air ﬁlterTensioning the recoil spring Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpSpark plug Cooling systemMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations, model Saw chain ﬁling and ﬁle gaugesFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions1150239-95 ´z+R7¶5B¨ ´z+R7¶5B¨