Husqvarna YTH180 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in "DISENGAGED" position.

•Turn ignition key "OFF" and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 23)

Mower will be easier to remove from the right side of tractor.

•Place attachment clutch switch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off electric clutch pulley.

•Disconnect anti-sway bar from chassis bracket by removing retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED TO THE TRACTOR, THE R.H. AND L.H. SUSPENSION ARMS MUST BE REMOVED FROM TRACTOR.

SUSPENSION	ELECTRIC
ARMS	ELECTRIC
	CLUTCH
	PULLEY
	RETAINER
	SPRINGS
	(BOTH SIDES)
RETAINER
SPRING
ANTI-SWAY BAR	RETAINER
	RETAINER
	SPRINGS
	(BOTH SIDES)

FIG. 23

TO INSTALL MOWER (See Fig. 23)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with discharge guard to right side of tractor.

•Lower lift lever to its lowest position.

•Install mower in reverse order of removal instructions.

19

Image 19

Contents YTH180 II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationCustomer Responsibilities Product SpecificationsModel Number YTH180 Serial Table of Contents Contents of Hardware Pack Before Rolling Tractor OFF Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts HOW to SET UP Your TractorCheck Tire Pressure Check Deck LevelnessTo Attach Front Bumper See Fig Install Battery See FigsAssemble Gauge Wheels to Mower Deck See Fig Install Mulcher Plate See Figs a & 8BTo Convert to Bagging or Discharging Know Your Tractor OperationHOW to USE Your Tractor To Operate on Hills Before Starting the EngineADD Gasoline To Start Engine See Fig Indicator LightsPurge Transmission Mulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartService Dates Customer Responsibilities Blade Care Tractor Brake Operation TiresTransaxle Pump Fluid EngineBelts Transaxle CoolingSpark Plugs CleaningEngine OIL Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Adjust Attachment Clutch See FigTo Adjust Brake See Fig Belt InstallationTransmission REMOVAL/REPLACEMENT To Adjust Motion Control Lever See FigTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Replace FuseInterlocks and Relays Acceleration Test Other StorageProblem Cause Correction Troubleshooting PointsOFF Wiring Insulated Clips PTO Switch SchematicIndicator Lights Ignition SwitchElectrical Repair PartsKEY Part NO. NO. Description Chassis and Enclosures KEY Part NO. no Description Drive KEY Part Description Steering Assembly KEY Part NO. no Description 118 HP 42 Tractor Model NO. YTH180 954001172A Seat AssemblyLBD48 Wheels & TiresLSB42 Optional Equipment Engine Mower Lift Assembly KEY Part NO. NO. Description Mower KEY Part NO. no Description HYDRO-GEAR Transaxle - Model Number Repair Parts Service Notes Service Notes Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationPerimeter Woods Drive Warranty StatementCHARLOTTE, North Carolina 532145464