Husqvarna Pro 18 AWD manual Checking the Parallelism of the Cutting Unit

Page 48

MAINTENANCE

Checking the Parallelism of the Cutting Unit

Check the cutting unit’s parallelism as follows:

1.Check the air pressure in the tyres 60 kPa / 0.6 bar / 9 PSI.

2.Place the Rider on a flat surface.

3.Put the lifting lever in the mowing position.

4.Measure the distance between the ground and the front and back edges of the unit’s cover. The cutting unit should have a slight slant, with the rear edge 2–4 mm (1/8") higher than the front edge.

Adjusting the Parallelism of the Cutting Unit

1.Remove the front cover and the right-hand wing cover.

2.Loosen the nuts on the parallel strut.

3Screw out (extend) the strut to raise the rear edge of the cover.

Screw in (shorten) the strut to lower the rear edge of the cover.

4.Tighten the nuts after adjustment.

5.The parallelism of the cutting unit should be checked again after the adjustment has been made.

6.Fit the right-hand wing cover and the front cover.

6017-217

6017-018

46 – English

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Rider Pro 15 Pro 18 Pro 18 AWD Page Contents Introduction CongratulationsDriving and Transport on Public Roads TowingProper Service Serial NumberKEY to Symbols Read the operator’s manualSafety Instructions Safety InstructionsGeneral Use Keep children away from the work area Driving on Slopes Proceed as followsMaintenance ChildrenAvoid sparking and its consequences by Wearing protective glassesTransport Presentation PresentationAccelerator Placement of Controls Cutting UnitThrottle Control Choke LeverChronometer Cutting Height Adjustment Lever Lifting Lever for the Cutting UnitLights and Power Outlet Parking BrakeSeat RefuellingDriving Mowing TipsClutch Control Rear AxleFront Axle Before Starting Starting the Engine8009-494 Driving the Rider BrakingStopping the Engine Maintenance Maintenance ScheduleDaily main Weekly3 At least Maintenance Tenance Once Interval hours Before AfterMaintenance Daily main Weekly3 At least Interval hours Main Once 100 300Dismantling the Rider Covers Engine CoverFront Cover Transmission CoverChecking and Adjusting the Steering Cables Left-hand Wing CoverAdjusting the Parking Brake Pro 15, Pro Adjusting the Parking Brake Pro 18 AWDChecking and Adjusting the Throttle Cable Checking and Adjusting the Choke CableInspecting the Muffler Cleaning the Pulse Air Filter Replacing the Fuel FilterChecking the Fuel Pump’s Air Filter Air Supply Exhaust PipeReplacing the Air Filter Pro 8009-148 8009-149 8009-150 8009-151 Cleaning the Engine and Muffler Checking the Engine’s Cooling Air IntakeChecking the Acid Level in the Battery Actions with acid contactFitting the wrong spark plug type can damage the engine Checking the Safety System Replacing the Light Bulbs Fuses Checking the Tyre PressuresReplacing the Rear Drive Belt Pro 15 and Pro RemovalAssembly Replacing the Hydraulic Pump’s Drive Belt Pro 18 AWD 8009-641 8009-640 8009-726 Replacing the Centre Belt Replacing the Front Belt Pro 15, Pro Replacing the Front Belt Pro 18 AWDDismantling 8009-122 Fitting the Cutting Unit Observe caution to avoid trapping your handRemoving the Cutting Unit Checking and Adjusting the Cutting Unit’s Ground Pressure Cutting HeightAdjusting the Parallelism of the Cutting Unit Checking the Parallelism of the Cutting Unit8009-287 Cutting Unit’s Service Position Placing in the Service Position6017-221 6017-222 8009-598 8009-122 6017-223 Releasing the Service Position Inspecting the Blades Removing the BioClip Plug Combi Lubrication Chart Pro Lubrication8009-504 Lubrication Chart Pro 18 AWD General Lubricating the CablesPedal Mechanism in Frame Tunnel Chains in the Frame TunnelThree-Point Link and Joints Driver’s SeatThrottle and Choke Cables, Lever Bearings Belt Tensioner Engine OilHydrostatic Cable with Linkage Changing the Engine OilParking Brake Cable Pro 15, Pro Transmission Oil Level Pro 15, ProHydraulic System and Transmission Oil level Pro 18 AWD Oil Filter, Change Hydraulic Fluid Filter, Replacing Pro 18, Pro 18 AWDParking Brake Cable Pro 18 AWD Right Rear Axle BearingTrouble Shooting Guide Problem CauseService StorageCover Wiring Diagram Colour Abbreviations8009-588 8009-679 Technical Data Dimensions Rider Pro Rider Pro 18 AWDCutting unit Combi EU Declaration of Conformity EU Declaration of Conformity Only applies to EuropeService Journal Delivery ServiceAfter the First 8 Hours Hour Service First after 50 hours 100/200-Hour Service Action Date, mileage reading, stamp SignatureService Journal At Least Once Each Season Action Date, mileage reading, stamp, signature Service Journal ´z+RÆh¶6j¨ English 115 00 2005W05

Pro 18 AWD specifications

The Husqvarna Pro 18 AWD is a state-of-the-art lawnmower designed for professional landscapers and gardening enthusiasts alike. Its robust engineering and innovative features make it stand out in the competitive market of outdoor power equipment.

One of the key features of the Pro 18 AWD is its all-wheel drive system (AWD), which enhances traction and control on varied terrains. This is particularly beneficial for properties with slopes or uneven ground, ensuring that the mower can maneuver smoothly without losing grip. The AWD system provides the user with confidence and stability, reducing the likelihood of slips and accidents during operation.

Equipped with a powerful engine, the Pro 18 AWD delivers consistent performance even in challenging conditions. The engine is designed for efficiency and durability, making it capable of handling thick grass and tough overgrowth with ease. The mower's cutting deck is adjustable, allowing users to choose their desired cutting height, providing flexibility for different grass types and landscapes.

Another standout feature of the Pro 18 is its cutting technology. The mower comes with a high-performance cutting deck that utilizes advanced blade design, ensuring clean and precise cuts. This results in a healthier lawn and a superior finish. Additionally, the mower incorporates a mulching capability, allowing grass clippings to be finely shredded and returned to the soil as natural fertilizer, promoting lawn health while reducing waste.

Ergonomics is a top priority in the design of the Husqvarna Pro 18 AWD. The adjustable handlebar and comfortable grip provide ease of use and reduce fatigue during extended periods of mowing. The lightweight construction enhances maneuverability, making it easier to navigate tight spots and obstacles in your yard.

Furthermore, the Husqvarna Pro 18 AWD is equipped with various safety features, including a blade brake that stops the blades quickly when the user releases the handle. This ensures safe operation and reduces the risk of accidents.

In summary, the Husqvarna Pro 18 AWD combines power, versatility, and user-friendly design, making it an ideal choice for both professionals and homeowners who demand top performance from their lawnmowers. With features like all-wheel drive, advanced cutting technology, ergonomics, and safety measures, this mower sets a new standard in the lawn care industry, ensuring that users can achieve a pristine lawn with ease and efficiency. Whether tackling residential lawns or larger commercial properties, the Pro 18 AWD is poised to deliver exceptional results.
Top Page Image Contents