Husqvarna Pro 18 AWD manual Hydrostatic Cable with Linkage, Changing the Engine Oil

Page 62

LUBRICATION

Changing the Engine Oil

The engine oil should be changed the first time after 8 hours running time. It should then be changed after every 100 hours of running time. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.

WARNING!

Engine oil can be very hot if it is drained directly after stopping the engine. Allow the engine to cool somewhat first.

1.Open the engine cover.

2.Place a container underneath the engine’s left oil drain plug.

3.Remove the dipstick. Remove the drain plug from the engine’s left side.

4.Let the oil run out into the container.

5.Then replace the oil drain plug and tighten it.

6.Replace the oil filter if necessary.

7.Fill with oil up to the FULL mark on the dipstick. Use engine oil as set out above.

8.Run the engine warm, then check that there is no leakage from the oil plug.

9.Check the oil level. Top up if necessary.

9.Hydrostatic Cable with Linkage

Remove the transmission cover, two screws.

Lubricate the joints and bearings on the left side with an oilcan.

Remove the rubber casing and lubricate the hydrostatic transmission cable with an oil can. Press the pedal a few times and lubricate again.

Replace the rubber cover.

Replace the transmission cover.

IMPORTANT INFORMATION

Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location.

Avoid skin contact; wash with soap and water in case of spills.

8009-529

6008-209

6020-024

60 – English

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Rider Pro 15 Pro 18 Pro 18 AWD Page Contents Driving and Transport on Public Roads IntroductionCongratulations TowingProper Service Serial NumberKEY to Symbols Read the operator’s manualGeneral Use Safety InstructionsSafety Instructions Keep children away from the work area Driving on Slopes Proceed as followsMaintenance ChildrenAvoid sparking and its consequences by Wearing protective glassesTransport Accelerator PresentationPresentation Placement of Controls Cutting UnitChronometer Throttle ControlChoke Lever Cutting Height Adjustment Lever Lifting Lever for the Cutting UnitSeat Lights and Power OutletParking Brake RefuellingDriving Mowing TipsFront Axle Clutch ControlRear Axle Before Starting Starting the Engine8009-494 Driving the Rider BrakingStopping the Engine Daily main Weekly3 At least Maintenance Tenance MaintenanceMaintenance Schedule Once Interval hours Before AfterMaintenance Daily main Weekly3 At least Interval hours Main Once 100 300Front Cover Dismantling the Rider CoversEngine Cover Transmission CoverChecking and Adjusting the Steering Cables Left-hand Wing CoverAdjusting the Parking Brake Pro 15, Pro Adjusting the Parking Brake Pro 18 AWDInspecting the Muffler Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Checking the Fuel Pump’s Air Filter Cleaning the Pulse Air FilterReplacing the Fuel Filter Air Supply Exhaust PipeReplacing the Air Filter Pro 8009-148 8009-149 8009-150 8009-151 Cleaning the Engine and Muffler Checking the Engine’s Cooling Air IntakeFitting the wrong spark plug type can damage the engine Checking the Acid Level in the BatteryActions with acid contact Checking the Safety System Replacing the Light Bulbs Fuses Checking the Tyre PressuresReplacing the Rear Drive Belt Pro 15 and Pro RemovalAssembly Replacing the Hydraulic Pump’s Drive Belt Pro 18 AWD 8009-641 8009-640 8009-726 Replacing the Centre Belt Dismantling Replacing the Front Belt Pro 15, ProReplacing the Front Belt Pro 18 AWD 8009-122 Fitting the Cutting Unit Observe caution to avoid trapping your handRemoving the Cutting Unit Checking and Adjusting the Cutting Unit’s Ground Pressure Cutting HeightAdjusting the Parallelism of the Cutting Unit Checking the Parallelism of the Cutting Unit8009-287 Cutting Unit’s Service Position Placing in the Service Position6017-221 6017-222 8009-598 8009-122 6017-223 Releasing the Service Position Inspecting the Blades Removing the BioClip Plug Combi Lubrication Chart Pro Lubrication8009-504 Lubrication Chart Pro 18 AWD General Lubricating the CablesPedal Mechanism in Frame Tunnel Chains in the Frame TunnelThrottle and Choke Cables, Lever Bearings Three-Point Link and JointsDriver’s Seat Belt Tensioner Engine OilHydrostatic Cable with Linkage Changing the Engine OilHydraulic System and Transmission Oil level Pro 18 AWD Parking Brake Cable Pro 15, ProTransmission Oil Level Pro 15, Pro Oil Filter, Change Hydraulic Fluid Filter, Replacing Pro 18, Pro 18 AWDParking Brake Cable Pro 18 AWD Right Rear Axle BearingTrouble Shooting Guide Problem CauseCover ServiceStorage Wiring Diagram Colour Abbreviations8009-588 8009-679 Technical Data Dimensions Rider Pro Rider Pro 18 AWDCutting unit Combi EU Declaration of Conformity EU Declaration of Conformity Only applies to EuropeAfter the First 8 Hours Service JournalDelivery Service Hour Service First after 50 hours 100/200-Hour Service Action Date, mileage reading, stamp SignatureService Journal At Least Once Each Season Action Date, mileage reading, stamp, signature Service Journal ´z+RÆh¶6j¨ English 115 00 2005W05

Pro 18 AWD specifications

The Husqvarna Pro 18 AWD is a state-of-the-art lawnmower designed for professional landscapers and gardening enthusiasts alike. Its robust engineering and innovative features make it stand out in the competitive market of outdoor power equipment.

One of the key features of the Pro 18 AWD is its all-wheel drive system (AWD), which enhances traction and control on varied terrains. This is particularly beneficial for properties with slopes or uneven ground, ensuring that the mower can maneuver smoothly without losing grip. The AWD system provides the user with confidence and stability, reducing the likelihood of slips and accidents during operation.

Equipped with a powerful engine, the Pro 18 AWD delivers consistent performance even in challenging conditions. The engine is designed for efficiency and durability, making it capable of handling thick grass and tough overgrowth with ease. The mower's cutting deck is adjustable, allowing users to choose their desired cutting height, providing flexibility for different grass types and landscapes.

Another standout feature of the Pro 18 is its cutting technology. The mower comes with a high-performance cutting deck that utilizes advanced blade design, ensuring clean and precise cuts. This results in a healthier lawn and a superior finish. Additionally, the mower incorporates a mulching capability, allowing grass clippings to be finely shredded and returned to the soil as natural fertilizer, promoting lawn health while reducing waste.

Ergonomics is a top priority in the design of the Husqvarna Pro 18 AWD. The adjustable handlebar and comfortable grip provide ease of use and reduce fatigue during extended periods of mowing. The lightweight construction enhances maneuverability, making it easier to navigate tight spots and obstacles in your yard.

Furthermore, the Husqvarna Pro 18 AWD is equipped with various safety features, including a blade brake that stops the blades quickly when the user releases the handle. This ensures safe operation and reduces the risk of accidents.

In summary, the Husqvarna Pro 18 AWD combines power, versatility, and user-friendly design, making it an ideal choice for both professionals and homeowners who demand top performance from their lawnmowers. With features like all-wheel drive, advanced cutting technology, ergonomics, and safety measures, this mower sets a new standard in the lawn care industry, ensuring that users can achieve a pristine lawn with ease and efficiency. Whether tackling residential lawns or larger commercial properties, the Pro 18 AWD is poised to deliver exceptional results.
Top Page Image Contents