Adjustments Motion Control Linkage Adjustment

ADJUSTMENTS

MOTION CONTROL LINKAGE ADJUSTMENT:

1.This adjustment must be made with the drive wheels rotating. Raise rear of the unit and block it up so the wheels are free to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires.

2.Tilt seat forward and remove the seat rod from seat so the seat can rotate down onto the frame. Make sure the seat is adjusted toward the rear of the unit so it clears the controls on the console.

3.Place a 2x4 board approximately 10 to 12 inches long between the foot plate and the center of the seat to engage the seat safety switch. NOTE: You may want to cover the end of the 2x4 with a rag to protect the seat from marring.

4.The reverse spring detent must be adjusted correctly before the motion control linkages may be adjusted.(See reverse spring detent adjustment section.)

5.Loosen the nuts directly behind each ball joint on both rods that connect the pump arm to the motion control assemblies. (See Fig 5 )

6.Start the engine. The park brake must be engaged and the motion control levers must be in the neutral slot (See figure 6 page10) to start the engine. Run engine at approximately 1/

2throttle.

7.Release park brake to allow wheels to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires.

8.Begin with either side and put the motion control lever into the neutral position. Adjust the motion control linkage by rotating the double nuts on the rod in the proper direction until the wheel stops rotating (See Fig 5 ).

Move the motion control lever forward then into the neutral position and place it into the neutral slot. The wheel must be stopped completely at this point. Now do the same in reverse and release the lever. The lever should return to neutral on its own. If not see reverse spring detent adjustment section.

9.Run engine at full throttle to make sure wheels do not rotate. Readjust if any rotation occurs.

10.Repeat on the opposite side and tighten nuts against ball joints.

11.Remove the 2x4 board and make sure the seat wiring is connected to the wiring harness. WARNING: Seat must be connected for safety interlock system to properly function.

OPERATING INSTRUCTIONS

CONTROLS:

1.Be thoroughly familiar with all controls their function and how to operate them before operating the mower.

2.Motion control levers located on each side of the console control direction of movement. The left lever controls the flow of oil from the left hydro pump to the left wheel motor. The right lever controls the flow of oil from the right hydro pump to the right wheel motor.

ZTH5225A, ZTH5223A, ZTH6125A specifications

Husqvarna, a renowned name in outdoor power equipment, offers a range of zero-turn lawn mowers, including the ZTH5223A, ZTH5225A, and ZTH6125A models. Each of these models showcases advanced technology and features designed to enhance lawn care efficiency and user comfort.

The Husqvarna ZTH5223A is equipped with a robust 23 HP Kawasaki engine, providing reliable power for tackling various lawn conditions. Its cutting deck spans 52 inches, making it nimble enough for tight spaces while ensuring a swift mowing experience. The fully adjustable seat, combined with ergonomic controls, ensures operator comfort during extended use. The ZTH5223A features a dual hydrostatic transmission, allowing smooth and responsive maneuvering.

Moving up to the ZTH5225A, this model boasts a slightly more powerful 25 HP Kawasaki engine. It retains the 52-inch cutting deck but introduces a premium suspension system to enhance ride quality over uneven terrain. The ZTH5225A also includes an advanced air filtration system, ensuring the engine operates efficiently while prolonging its life. Enhanced operator controls make this model intuitive to use, providing a seamless mowing experience.

The ZTH6125A stands out with its 61-inch cutting deck, making it ideal for larger properties. With a powerful 25 HP engine, this model combines power with efficiency, capable of tackling thick grass and more challenging landscapes. The ZTH6125A integrates a high-performance hydrostatic transmission, providing precise speed control and agility. The model also features a patented deck lifting system, allowing for easy height adjustments on-the-go.

All three models are designed with durability in mind, using premium-quality materials that stand up to the rigors of frequent use. They are equipped with easy-access maintenance points to simplify routines such as oil changes and blade replacement. Husqvarna’s commitment to technology is evident through their incorporation of features like the Air Induction mowing technology, ensuring an even cut and minimized clumping, regardless of grass type.

In summary, the Husqvarna ZTH5223A, ZTH5225A, and ZTH6125A offer a range of powerful features such as efficient engines, durable construction, and operator-centered designs. Whether for small residential lawns or expansive commercial spaces, these zero-turn mowers are engineered to deliver exceptional performance and a superior mowing experience.