Jensen Tools VM9511TS instruction manual Operating Instructions

Page 17
[RESET] Button

VM9511TS

OPERATING INSTRUCTIONS

Power On / Off

Press the /MUTE button (7) to turn the unit on. The buttons on the front of the unit light up and “WELCOME” appears briefly in the LCD panel (23), followed by the current mode status. If the TFT screen is open, only the current mode status is displayed. You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen.

Press and hold the /MUTE button (7) on the front panel or the POWER button (4) on the remote to power off the unit.The monitor is drawn back into the main compartment and the LCD screen displays “BYE BYE”.

Audible Beep Confirmation

An audible beep tone confirms each function selection. The beep tone cannot be disabled.

Mute

Press the /MUTE button (7) on the front panel or the MUTE button

(3)on the remote to mute the volume from the unit. Press the MUTE button again to restore the volume. “MUTE” is displayed on the LCD monitor. Adjusting the volume or using any of the audio setup features cancels the mute function.

Playing Source Selection

Press the SRC button (15) on the front panel or the SRC button (8) on the remote to change between available playing sources in the following order: TUNER, DVD, CD Changer, AUX IN, CAMERA (rear view video camera) and SD. The playing mode is displayed on the TFT and LCD screens.

AUX IN Mode

An external peripheral device can be connected to this unit via RCA output and “AUX-IN”.

CAMERA Mode

“CAMERA” mode is only available if the camera is connected and during reverse driving. To install a rear view video camera, connect the video input cable to the camera output cable.

Volume Adjustment

To increase or decrease the volume level, turn the ROTARY ENCODER (6) on the front panel or press the VOL+/ VOL- buttons (15, 16) on remote control. When the volume level reaches “0” or “40”, a beep sounds, indicating that the adjustment limit has been reached. The volume ranges from “0” to “40”. The LCD or TFT screen displays the volume level for 3 seconds.

Programmable Turn-On Volume

This feature allows the user to select a turn-on volume setting regardless of the volume setting prior to turning the unit off.

To program a specific volume level, push and hold the VOL/ LO/DX knob (6) while the yellow volume bar is displayed on the screen. The unit will beep two times to confirm your turn- on volume setting.

Audio Control Menu

The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. To get the best possible sound quality from your new system, be sure to adjust the settings for the speakers as well. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer.

Accessing the Audio Control Menu

Press the VOL/LO/DX knob (6) on the front panel once to display the “AUDIO” menu.

Selecting an Audio Feature for Adjustment

Continuously press the VOL/LO/DX knob (6) on the front panel, or press the (>>)/(<<) buttons (14, 22) on the remote control or the (/\)/ (V) buttons (18, 19) on the joystick to select the audio feature to be adjusted.

Adjusting an Audio Feature

Rotate the VOL/LO/DX knob (6), press the (<<)/(>>) buttons (17,

19)on the remote control, or press the (<)/(>) buttons (16, 17) on the joystick to adjust the selected feature to the desired setting.

Table 5: Audio Adjustments

Audio Function

Adjustable Range

 

 

 

 

EQ

User

 

Flat

 

 

 

Jazz

 

 

 

Pop

 

 

 

Classical

 

 

 

Rock

 

 

 

Vocal

 

 

BASS

-14 to +14

 

 

TREBL

-14 to +14

 

 

SUB

-7 to +7

 

 

LOUD

0 (off), 1-4

 

 

FAD (Fade)

-9 to +9

 

 

BAL

-9 to +9

 

 

NOTE: The Bass and Treble levels are only adjustable when EQ is set to “User” mode.

The Loud function compensates for deficiencies in sound ranges at low levels. Loudness levels range from 1-4 or “off”. When the Loud function is on, “LOUD” is displayed on the screen.

Exiting the Audio Control Menu

Press and hold the VOL/LO/DX knob (6) or stop making adjustments for a few seconds to exit the audio control menu.

Six-Channel Audio Control

NOTE: Before adjusting the volume of any speaker, please refer to “Surround Sound” on page 26.

Table 6: 6-Channel Audio Adjustments

Item

Adjustable Range

 

 

 

 

Master Volume

00 to 40

 

 

Front Left Channel Volume

-10 to +10

 

 

Front Right Channel Volume

-10 to +10

 

 

Rear Left Channel Volume

-10 to +10

 

 

Rear Right Channel Volume

-10 to +10

 

 

Center Channel Volume

-10 to +10

 

 

Subwoofer Volume

-10 to +10

 

 

Rear Zone

If a monitor is installed in the rear zone and connected to the rear zone AV output, passengers in the back seat can control the DVD output using the rear zone remote control. See “Multi-Zone Remote Control” on page 12 for instructions.

System Reset

To correct a system halt or other illegal operation, use the tip of a pen to press the RESET button (22) located on the front

bottom-right corner of the unit. After a system reset, the unit restores all factory default settings.

NOTE: If the unit is reset while a DVD is playing, the DVD resumes play once the reset is complete.

Line Mute

If the “MUTE” wire is connected, audio output mutes when a telephone call is received by the car phone or when verbal navigation is performed.

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents VM9511TS Table DES Matières ContentsContenido Tools and Supplies FeaturesPreparation IAUX3 Ready Sold Separately Disconnecting the BatteryWiring Diagram Wiring Diagram Multimedia Connections Installation Audio Controls and IndicatorsButton Operation 11 /RPT 10 /SCN12 /2-6CH/RDM 13 /STOPLCD Display/Indicators Front Zone Remote Control Function Front Zone Remote Control FunctionsRef# DVD VCD Tuner CD/MP3Function Name Ref# DVD VCD MULTI-ZONE Remote ControlMulti-Zone Remote Control Functions Button Name Ref # Using the TFT Monitor Monitor Protective Measures Monitor Movement MechanismOperating Instructions General Setup Menu System Setup MenuExiting the System Setup Menu ASP Audio Sound Processing Config MenuReturning to the System Setup Menu Accessing the ASP Config MenuSelecting a Source for the Front Zone MULTI-ZONE OperationSelecting a Source for the Rear Zone Multi-ZONE Source OptionsTuner Operation Channel/Category Guide Mode Preset ModeXM Radio Operation Displaying the Identification ID CodeXM Setup Menu Direct TuningCategory Guide Mode Diagnostic ModeDVD/VCD Video Operation Scanning Fast Forward/Fast ReverseSelecting 2-Channel and 6-Channel Audio Playback Goto SearchGeneral Disc Information Symbol MeaningVCD Playback Information Disc Properties Symbo 12cm Disc Properties Max PlayAccessing the DVD Setup Screen DVD/DISC Setup MenuAccessing a Menu Language MenuSurround Sound SPK Config MenuAudio Menu Rating Parental Lock Menu Pro-Logic II Menu Features Setting Options FunctionRating Menu Features Setting Options Function MP3/WMA Operation DVD/DISC Audio OperationCD Player User Interface VM9511TS SD Card Reader Operation Accessing SD Card ModeChange Directory Previous/NextControlling your iPod Accessing iPod ModeIpod Operation TV Tuner Operation Navigation System Problem Cause Corrective Action TroubleshootingTroubleshooting Message Displayed Cause Corrective Action Error MessagesError Messages Care and Maintenance CEA Power Ratings SpecificationsMonth Limited Warranty

VM9511TS specifications

The Jensen Tools VM9511TS is a versatile tool that stands out in the realm of industrial and electronic maintenance. Designed for professionals who demand high performance and reliability, this tool encompasses several features and technologies that cater to a wide array of demanding tasks.

One of the primary characteristics of the VM9511TS is its robust build quality. Crafted from durable materials, it ensures longevity and withstands the rigors of heavy usage. The ergonomic design allows for comfortable handling, enabling users to work for extended periods without experiencing fatigue. This thoughtful design extends to the tool's weight distribution, making it easy to maneuver, even in tight spaces.

Equipped with a powerful motor, the VM9511TS delivers exceptional torque and speed, ensuring efficient performance for a variety of applications. The tool’s variable speed control allows users to adjust the speed settings according to the specific requirements of the task at hand, providing the flexibility needed for both delicate and rigorous jobs.

One of the standout technologies integrated into the VM9511TS is its electronic overload protection system. This feature not only enhances safety but also prolongs the life of the tool by preventing it from overheating during prolonged use. Additionally, the tool boasts a quick-change chuck, allowing for rapid swapping of bits and attachments, which saves critical time on the job.

The VM9511TS is also notable for its compact design, making it ideal for use in confined spaces. This design does not compromise on power, as the tool maintains impressive capability while remaining portable. Users will find that the tool’s light weight further aids in reducing strain, making it a go-to option for professionals who require mobility without sacrificing performance.

Other distinctive features include an LED light that illuminates the workspace, ensuring visibility even in dimly lit areas. This is particularly useful when working in tight spots or during late hours. The tool comes with a comprehensive set of compatible accessories, providing users with everything they need to get started immediately.

In summary, the Jensen Tools VM9511TS is a top-tier tool designed for versatility and efficiency. Its combination of robust construction, advanced technology, and user-friendly features makes it an indispensable asset for professionals in various fields, from electronics to general maintenance.
Top Page Image Contents