Husqvarna LTH125 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 20

SERVICE AND ADJUSTMENTS

CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

Depress clutch/brake pedal fully and set parking brake.

Place motion control lever in neutral (N) position.

Place attachment clutch in "DISENGAGED" position.

Turn ignition key "OFF" and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 21)

Mower will be easier to remove from the right side of tractor.

• Place attachment clutch in “DISENGAGED” position.

• Move attachment lift lever forward to lower mower to its

lowest position.

• Roll belt off engine pulley.

• Disconnect clutch rod from clutch lever by removing

retainer spring.

• Disconnect anti-sway bar from chassis bracket by

removing retainer spring.

• Disconnect suspension arms from rear deck brackets

CLUTCH LEVER

CLUTCH ROD

RETAINER SPRING

SUSPENSION

ENGINE

ARMS

PULLEY

 

 

by removing retainer springs.

Disconnect front links from deck by removing retainer

 

springs.

Raise lift lever to raise suspension arms. Slide mower

 

out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED TO THE TRACTOR, THE R.H. AND L.H. SUSPENSION ARMS MUST BE REMOVED FROM TRACTOR.

TO INSTALL MOWER (See Fig. 21)

Raise attachment lift lever to its highest position.

Slide mower under tractor with discharge guard to right side of tractor.

Lower lift lever to its lowest position.

Install mower in reverse order of removal instructions.

RETAINER

SPRING

ANTI-SWAY BAR

RETAINER

SPRINGS (BOTH SIDES)

RETAINER

SPRINGS (BOTH SIDES)

FIG. 21

20

Image 20
Contents LTH125 Safety Rules Safe Operation Practices for Ride-On MowersModel Number LTH125 Serial Product SpecificationsCustomer Responsibilities Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Rolling Tractor OFF SkidHOW to SET UP Your Tractor Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsInstall Battery See Figs Install Mulcher Plate See Figs.6 To Convert to Bagging or DischargingOperation Know Your TractorHOW to USE Your Tractor ADD Gasoline Before Starting the EngineTo Operate on Hills Page Mowing Tips Mulching Mowing TipsLubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Brake OperationTires Blade CareBattery See Fig To Clean Battery and TerminalsBelts Transaxle CoolingClean AIR Screen See Fig EngineLubrication AIR Filter See FigCleaning Engine Cooling Fins See FigMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt SeeTo Adjust Motion Control Lever See Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig To Remove Hood and Grill Assembly SeeTo Replace Fuse To Replace Headlight BulbTo Adjust Throttle Control Cable See To Adjust Carburetor See FigPreliminary Setting Final SettingStorage OtherTroubleshooting Points Problem Cause CorrectionOFF Schematic TRACTOR- -MODEL NO. LTH125 HC125H42C ElectricalKEY Part Description NO. no Chassis and Enclosures KEY Part Description Drive Repair Parts Steering and Front Axle Repair Parts Engine Repair Parts Seat LBD48 Wheels and TiresLSB42 Lift KEY Part NO. NO. Description Page Mower Deck HYDRO-GEAR Transaxle Model no KEY Part NO. no Description Service Notes Service Notes Page Warranty Statement Husqvarna Forest & Garden CORev