Husqvarna LTH125 Install Mulcher Plate See Figs.6, To Convert to Bagging or Discharging

Page 9

ASSEMBLY

INSTALL MULCHER PLATE (See Figs.6 & 7)

Install two latch hooks to mulcher plate using screw, washer, lock washer, and weld nut as shown.

NOTE: Pre-assemble weld nut to latch hook by inserting weld nut from the top with hook pointing down.

Tighten hardware securely.

Raise and hold deflector shield in upright position.

Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

Hook front latch into hole on front of mower deck.

Hook rear latch into hole on back of mower deck.

CAUTION: Do not remove discharge guard from mower. Raise and hold guard when attaching mulcher plate and allow it to rest on plate while in operation.

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

HOOK POINTS

WELD NUTDOWN FROM THE TOP

LOCK

WELD WASHER

NUT

SCREW

LATCH

HOOKLATCH HOOK

LOCK WELD WASHER NUT

WASHER

WASHER

MULCHER

SCREW

PLATE

 

FIG. 6

DEFLECTOR

SHIELD

LATCH

HOOKS

FIG. 7

CHECKLIST

BEFORE YOU OPERATE AND ENJOY YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

All assembly instructions have been completed.

No remaining loose parts in carton.

Battery is properly prepared and charged. (Minimum 1 hour at 6 amps).

Seat is adjusted comfortably and tightened securely.

All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

Check wiring. See that all connections are still secure and wires are properly clamped.

Before driving tractor, be sure freewheel control is in drive position.

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

Engine oil is at proper level.

Fuel tank is filled with fresh, clean, regular unleaded gasoline.

Become familiar with all controls - their location and function. Operate them before you start the engine.

Be sure brake system is in safe operating condition.

It is important to purge the transmission before operat- ing your tractor for the first time. Follow proper starting and transmission purging instructions (See "TO START ENGINE" and "PURGE TRANSMISSION" in Opera- tion section of this manual).

9

Image 9
Contents LTH125 Safe Operation Practices for Ride-On Mowers Safety RulesProduct Specifications Customer ResponsibilitiesModel Number LTH125 Serial Table of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Rolling Tractor OFF SkidCheck Tire Pressure HOW to SET UP Your TractorCheck Deck Levelness Check for Proper Position of ALL BeltsInstall Battery See Figs To Convert to Bagging or Discharging Install Mulcher Plate See Figs.6Know Your Tractor OperationHOW to USE Your Tractor Before Starting the Engine To Operate on HillsADD Gasoline Page Mulching Mowing Tips Mowing TipsCustomer Responsibilities Lubrication ChartGeneral Recommendations Before Each USEBrake Operation TractorTires Blade CareTo Clean Battery and Terminals Battery See FigBelts Transaxle CoolingEngine Clean AIR Screen See FigLubrication AIR Filter See FigEngine Cooling Fins See Fig CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt SeeTransmission REMOVAL/REPLACEMENT To Adjust Motion Control Lever SeeTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Remove Hood and Grill Assembly See To Start Engine with a Weak Battery See FigTo Replace Fuse To Replace Headlight BulbTo Adjust Carburetor See Fig To Adjust Throttle Control Cable SeePreliminary Setting Final SettingOther StorageProblem Cause Correction Troubleshooting PointsOFF Schematic Electrical TRACTOR- -MODEL NO. LTH125 HC125H42CKEY Part Description NO. no Chassis and Enclosures KEY Part Description Drive Repair Parts Steering and Front Axle Repair Parts Engine Repair Parts Seat Wheels and Tires LSB42LBD48 Lift KEY Part NO. NO. Description Page Mower Deck HYDRO-GEAR Transaxle Model no KEY Part NO. no Description Service Notes Service Notes Page Husqvarna Forest & Garden CO Warranty StatementRev