Husqvarna How to Adjust the Carburetor on a Lawn Mower: Key Steps for Optimal Performance
Page 23

SERVICE AND ADJUSTMENTS

TO ADJUST CARBURETOR (See Fig. 34)

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjust- ment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows:

In general, turning idle mixture valve in (clockwise) de- creases the supply of fuel to the engine giving a leaner fuel/ air mixture. Turning the idle mixture valve out (counter- clockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: DAMAGE TO THE NEEDLE VALVE AND THE SEAT IN CARBURETOR MAY RESULT IF SCREW IS TURNED IN TOO TIGHT.

PRELIMINARY SETTING -

•Air cleaner assembly must be assembled to the carbu- retor when making carburetor adjustments.

•Be sure the throttle control cable is adjusted properly (see above).

•With engine off turn idle mixture valve in (clockwise) closing it finger tight and then turn out (counterclock- wise) 1 full turn.

FINAL SETTING -

•Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position.

•Move throttle control lever to slow () position. With finger, rotate and hold throttle lever against idle speed screw. Turn idle speed screw to attain 1750 RPM.

•While still holding throttle lever against idle speed screw, turn idle mixture valve in (clockwise) until en- gine begins to die and then turn out (counterclockwise) until engine runs rough. Turn valve to a point midway between those two positions. Release throttle lever.

ACCELERATION TEST -

• Move throttle control lever from slow () to fast ( ) position. If engine hesitates or dies, turn idle mixture valve out (counterclockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until engine acceler- ates smoothly.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

THROTTLE

IDLE SPEED

LEVER

SCREW

 

IDLE MIXTURE

 

VALVE

FIG. 34

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents LT130 II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationModel Number LT130 Serial Product SpecificationsCustomer Responsibilities Table of Contents Contents of Hardware Pack Before Rollingtractor OFF Skid AssemblyTools Required for Assembly To Remove Tractor from CAR- TONInstall Seat See Fig Connect Battery See FigsAssemble Gauge Wheels to Mower Deck See Fig Install Mulcher Plate See FigsTo Attach Nose Roller See Fig Check for Proper Position of ALL Belts To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessKnow Your Tractor OperationHOW to USE Your Tractor ADD Gasoline Before Starting the EngineTo Operate on Hills To TransportMulching Mowing Tips Mowing TipsTo Start Engine See Fig Before Each USE Lubrication ChartCustomer Responsibilities General RecommendationsTires BatteryTractor Brake OperationLubrication EngineBelts Transaxle CoolingSpark Plugs CleaningMuffler To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Transaxle Shifter Linkage and AD- Justment See FigsInterlocks and Relays To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Replace Headlight BulbAcceleration Test To Adjust Carburetor See FigPreliminary Setting Final SettingEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsOFF Tractor Model NO. LT130 954830071A SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures Bracket Pnt Fender Drive KEY Part NO. no Description Steering Assembly KEY Part Description NO. no 532140838 Seat Seat AssemblyLBD48 DecalsWheels & Tires KEY Part DescriptionEngine Optional EquipmentStud 1/4 turn Mower Deck 532141043 Guard TUV Idler Mower Lift Repair Parts Dana Transaxle Model Number Repair Parts Slope Sighting Guide CUT This OUT Dotted Is aPerimeter Woods Drive CHARLOTTE, North Carolina Husqvarna Forest & Garden CO532150710 09.22.95 TR

LT130 specifications

The Husqvarna LT130 is a ride-on lawn mower designed for homeowners seeking efficiency, comfort, and precision in their lawn care tasks. This model strikes a balance between performance and ease of use, making it an ideal choice for those with medium to large-sized yards.

At the heart of the LT130 is its powerful engine, which provides robust performance for tackling various terrains and grass types. The mower is equipped with a reliable Briggs & Stratton engine that offers ample power while ensuring fuel efficiency. This feature is vital for homeowners who wish to maintain their lawns without incurring excessive operational costs.

One of the prominent features of the LT130 is its cutting deck, which measures 97 cm (approximately 38 inches) in width. This size allows for quick mowing sessions, reducing the time spent on lawn care while providing a clean and even cut. The adjustable cutting heights, ranging from 30 mm to 75 mm, give users the flexibility to customize the mower's performance according to their lawn conditions and preferences.

The LT130 incorporates Husqvarna's innovative Reverse Motion technology, which enables users to mow in reverse without having to disengage the cutting blades. This is particularly useful for navigating tight spaces, around flower beds, and obstacles, facilitating a more efficient mowing experience.

Comfort is a focal point in the design of the LT130. The ergonomically designed seating and controls ensure that users can operate the mower with minimal fatigue. The easily accessible controls are intuitive and designed for user-friendliness, making it suitable for inexperienced operators. Additionally, the integrated cup holder and storage compartment enhance the overall convenience of the mower.

The Husqvarna LT130 also features a durable build that can withstand the rigors of regular lawn maintenance. The rugged chassis and high-quality materials provide longevity and reliability, ensuring that the mower serves homeowners well for years to come.

For added versatility, the LT130 is compatible with various attachments, such as baggers and mulch kits, allowing users to manage grass clippings in different ways. This adaptability makes it a multi-functional tool for landscape management.

In summary, the Husqvarna LT130 is a robust ride-on lawn mower that combines power, efficiency, and comfort. With its strong engine, adjustable cutting deck, and user-friendly features, it caters to the needs of homeowners looking to maintain a healthy and attractive lawn. Its durability and adaptability further solidify its reputation as a wise investment for lawn care enthusiasts.
Top Page Image Contents