Husqvarna LT130 Tools Required for Assembly, To Remove Tractor from CAR- TON, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

7/16" wrenches

Phillips Screwdriver

(1)

1/2" wrench

Tire pressure gauge

(1)

9/16" wrench

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton (See page 5).

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE ROLLINGTRACTOR OFF SKID

ATTACH STEERING WHEEL (See Fig. 1)

PREASSEMBLE SLEEVE TO STEERING WHEEL (See Fig. 1 Inset)

•Install sleeve retainer clips, evenly spaced around steering wheel hub, with formed tabs toward the out- side of hub.

•Press or lightly tap retainer clips fully onto steering wheel hub.

•Press steering sleeve fully onto steering wheel hub and clips.

ASSEMBLE EXTENSION SHAFT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extention and lower shafts and install 5/16 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 18-22 FT. LBS TORQUE.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Slide steering wheel adapter onto steering shaft exten- sion.

•Position steering wheel and sleeve assembly so cross bars are horizontal (left to right) and slide onto adapter.

•Assemble large flat washer and 3/8-24 locknut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective plastic from tractor hood and grill.

 

INSERT

 

3/8-24 LOCKNUT

 

LARGE FLAT

 

WASHER

STEERING

 

WHEEL

 

RETAINER CLIP

 

(TAB TO OUTSIDE)

STEERING

 

SLEEVE

STEERING

 

WHEEL HUB

 

 

ADAPTER

 

EXTENSION SHAFT

 

5/16 HEX BOLT

STEERING

 

SLEEVE

 

5/16 LOCKNUT

 

LOWER

 

STEERING

 

SHAFT

 

FIG. 1

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

TO ROLL TRACTOR OFF SKID (See Fig. 8)

•Raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor backwards off skid.

•Remove banding holding discharge guard up against tractor.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents LT130 General Operation IV. ServiceSafe Operation Practices for Ride-On Mowers II. Slope OperationProduct Specifications Customer ResponsibilitiesModel Number LT130 Serial Table of Contents Contents of Hardware Pack To Remove Tractor from CAR- TON AssemblyTools Required for Assembly Before Rollingtractor OFF SkidConnect Battery See Figs Install Seat See FigInstall Mulcher Plate See Figs To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig Check Deck Levelness To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your TractorHOW to USE Your Tractor To Transport Before Starting the EngineTo Operate on Hills ADD GasolineMowing Tips To Start Engine See FigMulching Mowing Tips General Recommendations Lubrication ChartCustomer Responsibilities Before Each USEBrake Operation BatteryTractor TiresTransaxle Cooling EngineBelts LubricationCleaning MufflerSpark Plugs Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Motion Drive Belt See FigTransaxle Shifter Linkage and AD- Justment See Figs To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig Interlocks and RelaysFinal Setting To Adjust Carburetor See FigPreliminary Setting Acceleration TestFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor Model NO. LT130 954830071AElectrical KEY Part NO. NO. Description Chassis and Enclosures Bracket Pnt Fender Drive KEY Part NO. no Description Steering Assembly KEY Part Description NO. no Seat Assembly 532140838 SeatKEY Part Description DecalsWheels & Tires LBD48Optional Equipment EngineStud 1/4 turn Mower Deck 532141043 Guard TUV Idler Mower Lift Repair Parts Dana Transaxle Model Number Repair Parts Sighting Guide CUT This OUT Dotted Is a SlopeHusqvarna Forest & Garden CO Perimeter Woods Drive CHARLOTTE, North Carolina532150710 09.22.95 TR

LT130 specifications

The Husqvarna LT130 is a ride-on lawn mower designed for homeowners seeking efficiency, comfort, and precision in their lawn care tasks. This model strikes a balance between performance and ease of use, making it an ideal choice for those with medium to large-sized yards.

At the heart of the LT130 is its powerful engine, which provides robust performance for tackling various terrains and grass types. The mower is equipped with a reliable Briggs & Stratton engine that offers ample power while ensuring fuel efficiency. This feature is vital for homeowners who wish to maintain their lawns without incurring excessive operational costs.

One of the prominent features of the LT130 is its cutting deck, which measures 97 cm (approximately 38 inches) in width. This size allows for quick mowing sessions, reducing the time spent on lawn care while providing a clean and even cut. The adjustable cutting heights, ranging from 30 mm to 75 mm, give users the flexibility to customize the mower's performance according to their lawn conditions and preferences.

The LT130 incorporates Husqvarna's innovative Reverse Motion technology, which enables users to mow in reverse without having to disengage the cutting blades. This is particularly useful for navigating tight spaces, around flower beds, and obstacles, facilitating a more efficient mowing experience.

Comfort is a focal point in the design of the LT130. The ergonomically designed seating and controls ensure that users can operate the mower with minimal fatigue. The easily accessible controls are intuitive and designed for user-friendliness, making it suitable for inexperienced operators. Additionally, the integrated cup holder and storage compartment enhance the overall convenience of the mower.

The Husqvarna LT130 also features a durable build that can withstand the rigors of regular lawn maintenance. The rugged chassis and high-quality materials provide longevity and reliability, ensuring that the mower serves homeowners well for years to come.

For added versatility, the LT130 is compatible with various attachments, such as baggers and mulch kits, allowing users to manage grass clippings in different ways. This adaptability makes it a multi-functional tool for landscape management.

In summary, the Husqvarna LT130 is a robust ride-on lawn mower that combines power, efficiency, and comfort. With its strong engine, adjustable cutting deck, and user-friendly features, it caters to the needs of homeowners looking to maintain a healthy and attractive lawn. Its durability and adaptability further solidify its reputation as a wise investment for lawn care enthusiasts.
Top Page Image Contents