Husqvarna GTH26V52LS To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

K

J

L

Fig. 7

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents GTH26V52LS General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Using the Reverse Operation SystemTo Stop Mower Blades To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig O PSecure with small washer and small retainer spring as shown To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel See FigReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove CABLES, Reverse Order Transmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionEngine continues KEY Part Description DecalsWheels and Tires KEY Part NO. NO. DescriptionSchematic SCH12Electrical KEY Part Description Chassis 234Tractor Model NO. GTH26V52LS 96043011800, Product no 43 Drive G7-BCBB-1XDC-1FCA Engine Spark Arrester KITSeat Assembly Steering Assembly 532 41 Wheel, Steering 532 19 Mower Deck Tractor Model NO. GTH26V52LS 96043011800, Product no 43 Mower Lift    Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX11.09.10 BAD

GTH26V52LS specifications

The Husqvarna GTH26V52LS is a versatile and high-performing lawn tractor designed for homeowners seeking efficiency and power in their mowing experience. With its robust construction and innovative features, this machine is ideal for tackling a variety of landscaping tasks with ease.

At the heart of the GTH26V52LS lies a strong 26 HP Kohler engine, ensuring reliable performance and the ability to handle larger properties. The engine is equipped with a hydrostatic transmission, which provides a seamless driving experience by allowing the operator to change speeds without the need for manual shifting. This feature makes it particularly user-friendly, as it enables smooth acceleration and greater control when navigating around obstacles.

One of the standout characteristics of the Husqvarna GTH26V52LS is its cutting deck. The 52-inch reinforced cutting deck offers a wide cutting path, enabling the user to cover more ground in less time. It features an air induction technology that enhances grass lift, resulting in an even and precise cut, regardless of the height or type of grass. The deck can be easily adjusted to different cutting heights, providing flexibility to meet individual lawn care needs.

Designed with user comfort in mind, the GTH26V52LS includes ergonomic features such as a high-back seat and easy-to-reach controls, allowing for extended periods of comfortable operation. The steering wheel is positioned for optimal maneuverability, which is essential when mowing in tight spaces or around landscaping features.

Another notable technology integrated into this lawn tractor is the automatic choke system, which simplifies the starting process by ensuring the engine starts quickly and efficiently in varying weather conditions. This innovation reduces the chances of flooding the engine and enhances overall reliability.

Durability is a key characteristic of the Husqvarna GTH26V52LS. Constructed with high-quality materials and precision-engineered components, this lawn tractor is built to withstand the rigors of regular use. Additionally, maintenance is made easy with accessible engine components and a removable cutting deck, allowing users to perform routine tasks without hassle.

In conclusion, the Husqvarna GTH26V52LS is an outstanding lawn tractor that combines power, comfort, and innovative technology to deliver exceptional mowing performance. Its user-friendly features and durability make it an excellent choice for homeowners looking to enhance their lawn care regimen.
Top Page Image Contents