Husqvarna GTH2654 owner manual Repair Parts

Page 37

REPAIR PARTS

TRACTOR - - MODEL NO. GTH2654 (96023000600) PRODUCT NO. 960 23 00-06

STEERING ASSEMBLY

KEY

PART

 

NO.

NO.

DESCRIPTION

1

532 19 36-51

Wheel, Steering

2

532 17 85-57 Axle Asm., Front

3

532 18 32-26

Fitting, Grease

4532 16 18-49 Spindle Asm, LH

5532 16 18-48 Spindle Asm., RH

6532 12 49-31 Bearing, Race Thrust Harden

7532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.

8812 00 00-29 Ring, Klip #T5304-75

9

532 12 12-32 Cap, Spindle

10874 78 10-44 Bolt, Fin Hex 5/8-11 x 2-3/4

11532 13 65-18 Spacer Brg Axle Front 1.570

12873 90 10-00 Nut, Lock Flange 5/8-11 unc

13532 12 17-49 Washer 25/32 x 1-1/4 x 16 Ga.

14810 04 06-00 Washer, Lock Hvy Hlcl Spr 3/8

15873 54 06-00 Nut Crownlock 3/8-24

16532 18 68-14 Shaft Asm., Steering

18

532 18 77-99

Draglink, Vgt

19

532 15 60-11 Support Asm., Steering Vgt

20

532 17 75-92

Boot Steering

21

532 18 67-37 Adapter, Wheel Steering

22

532 15 51-05

Bushing, Strg.

23

532 15 29-27

Screw

26532 19 36-52 Cap , Wheel Steering

27532 12 49-37 Bearing, Col. Strg.

28817 00 06-12 Screw 3/8-16 x 3/4

29

532 10 42-39 Bearing, Flange

31532 13 81-36 Bushing, Nyliner Snap

32819 11 16-10 Washer 11/32 x 1 x 10 Ga.

33810 04 05-00 Washer, Lock Hvy Hlcl Spr 5/16

34874 78 05-12 Bolt, Hex Hd 5/16-18 x 3/4

35532 18 70-39 Gear, Sector Steering

36 532 18 67-99 Tie Rod

41532 15 52-46 Bracket Switch Inerlock VGT97

42817 49 05-08 Screw 5/16-18 x 1/2

45819 18 38-12 Washer 9/16 ID x 2-3/8 OD 12 G Zin

46819 13 16-10 Washer 13/32 x 1 x 10 Ga.

47532 17 94-71 Bracket Asm. Idler

49

532 17 58-20 Pulley Idler Flat

50873 90 06-00 Nut Lock Flg 3/8-16 unc

51873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf

52532 17 55-53 Clip Steering .750

53532 18 89-67 Washer Harden .793 x 1.63 x 060

NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

37

Image 37
Contents GTH2654 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See a and 4B To Attach Nose Roller See Fig Install Mower and Drive Belt SeeCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Height Adjustment Knob Used to adjust the mower heightHOW to USE Your Tractor Using the Reverse Operation System To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal Belt RoutingTo Check and Adjust Brake To Adjust Attachment Clutch See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model NO. GTH2654 96023000600 Product no 23 SchematicElectrical KEY Part Description 138 Chassis and EnclosuresRepair Parts 153 Ground DriveRepair Parts Steering Assembly Repair Parts Engine Engine Briggs, Model No Order parts from engine 532 18 Seat Seat AssemblyWheels & Tires DecalsLift Assembly Repair Parts Mower Deck Repair Parts Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWarranty Statement 532 19 66-61 Rev 3.17.05 RD