Husqvarna GTH2654 owner manual Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 20

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 18)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod from lock bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove mower belt from electric clutch pulley.

•DISCONNECT REAR MOWER PINS Pull out the spring loaded pin, disconnect suspension arm from pin and release pin.

•Go to other side of mower and disconnect rear pin in the same manner.

•Remove the four retainer springs and two ﬂanged pins from front plate assembly and remove plate.

•Raise attachment lift lever to its highest position.

•Turn tractor steering wheel to the left as far as it will go.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Follow procedure described in “INSTALL MOWER AND DRIVE BELT” in the Assembly section of this manual. NOTE: You will need to reattach front plate assembly to tractor after sliding mower under the tractor.

	LOCKING BRACKET
BELT TENSION
ROD
DISENGAGED
POSITION	SUSPENSION ARMS

ELECTRIC CLUTCH

PULLEY

FRONT PLATE

ASSEMBLY

SINGLE LOOP

RETAINER SPRINGS

DOUBLE LOOP

RETAINER SPRINGS

FLANGED PINS

REAR MOWER

PINS

FIG. 18

20

Image 20

Contents GTH2654 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See a and 4B Install Mower and Drive Belt See To Attach Nose Roller See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance Lubrication ChartGeneral Recommendations Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Installation To Replace Mower Drive Belt See FigMower Drive Belt Removal Belt RoutingTo Adjust Attachment Clutch See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model NO. GTH2654 96023000600 Product no 23Electrical KEY Part Description Chassis and Enclosures 138Repair Parts Ground Drive 153Repair Parts Steering Assembly Repair Parts Engine Engine Briggs, Model No Order parts from engine Seat Assembly 532 18 SeatDecals Wheels & TiresLift Assembly Repair Parts Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 19 66-61 Rev 3.17.05 RD