Husqvarna GTH2654 To Replace Mower Drive Belt See Fig, Mower Drive Belt Removal, Belt Routing

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER DRIVE BELT (See Fig. 23)

MOWER DRIVE BELT REMOVAL

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod from lock bracket.

CAUTION: Belt tension rod is spring loaded. Have a ﬁrm grip on rod and release slowly.

•Remove screws from R.H. and L.H. mandrel covers and remove covers.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

MOWER DRIVE BELT INSTALLATION

•Install belt around both mandrel pulleys and around idler pulleys as shown.

•Install belt onto electric clutch pulley.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Reassemble R.H. and L.H. mandrel covers. Securely tighten all screws.

•Engage belt tension rod on locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

•Remove belt from electric clutch pulley, both mandrel pulleys and all idler pulleys.

BELT ROUTING

	L.H. MANDREL
	COVER
	LOCKING BRACKET
BELT TENSION	ELECTRIC
ROD (DISENGAGED	ELECTRIC
POSITION)	CLUTCH
	PULLEY

R.H. MANDREL

COVER

R.H.

MANDREL

IDLER

PULLEYS

FIG. 23

22

Image 22

Contents GTH2654 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See a and 4B Install Mower and Drive Belt See To Attach Nose Roller See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigUsing the Reverse Operation System Reverse Operation System ROSCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceLubrication Chart Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Drive Belt See Fig Belt RoutingTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Attachment Clutch See FigTo Check and Adjust Brake Transmission REMOVAL/REPLACEMENTReplacing Battery See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model NO. GTH2654 96023000600 Product no 23Electrical KEY Part Description Chassis and Enclosures 138Repair Parts Ground Drive 153Repair Parts Steering Assembly Repair Parts Engine Engine Briggs, Model No Order parts from engine Seat Assembly 532 18 SeatDecals Wheels & TiresLift Assembly Repair Parts Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 19 66-61 Rev 3.17.05 RD