Husqvarna GTH2448T To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10
FIG.9

OPERATION

J

FIG. 7

•Start tractor with motion control lever in neutral (N) position.

•Release parking brake.

•Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield (S) in place.

S

FIG. 10

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 917.279260 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor StoppingTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig Reverse Operation System ROSTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips Maintenance Before Each USEBrake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig To Level Mower Turn nut right Turn nut left To raise mower To Replace Motion Drive Belt See Fig Mower Drive Belt InstallationTo Replace Mower Blade Drive Belt See Fig Mower Drive Belt RemovalTo Check Brake To Start Engine with a Weak Battery See FigBelt Installation Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Schematic Tractor Model no .279260 GTH2448T, Product no 43Electrical KEY Part NO. NO. Description Chassis KEY Part Description Drive KEY Part NO. NO. Description Steering Assembly Spark Arrester KIT EngineSeat Assembly Decals Wheels and TiresMower Deck Tractor Model no .279260 GTH2448T, Product no 43 Mower Lift Tractor Model no .279260 GTH2448T, Product no 43 900 Key Part Description Tractor - Model Number Briggs Engine Model Number 445677, Type Number 0476-E1Carburetor Gasket SET 789A 1054 789B 1070 668 526 501 1005 474 877 332 1059 573 KEY Part Description Repair Parts Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

GTH2448T specifications

The Husqvarna GTH2448T is a remarkable lawn tractor designed for homeowners with medium to large-sized yards. Combining power, efficiency, and innovative features, the GTH2448T enhances your mowing experience while ensuring impressive performance.

At the heart of the GTH2448T is a robust 24 HP Kohler engine. This powerful engine provides ample torque and reliability, making it ideal for handling various terrains and mowing conditions. The automatic transmission allows for smooth driving and easy operation, enabling users to navigate around obstacles and tight spaces with confidence.

One of the standout features of the Husqvarna GTH2448T is its 48-inch cutting deck. This deck size strikes an excellent balance between maneuverability and mowing efficiency, allowing users to cover larger areas quickly while still being able to access narrow paths. The cutting height is adjustable, with options ranging from 1.5 inches to 4 inches, ensuring that you can customize your lawn's appearance according to your preferences.

The GTH2448T comes equipped with a tight turning radius, enhancing its agility and allowing for easier navigation in confined spaces. This feature is particularly valuable when mowing around flower beds, trees, and other landscape features. Additionally, the mower's ergonomic design ensures a comfortable riding experience, with a plush seat and user-friendly controls that are within easy reach.

The Husqvarna GTH2448T employs several innovative technologies, including the Air Induction Mowing Technology. This feature enhances airflow within the deck, promoting an even cut and reducing the chance of clumping, which results in a cleaner lawn appearance. Moreover, the tractor's durable construction and high-quality materials offer long-lasting performance, ensuring that your investment will stand the test of time.

For added convenience, the GTH2448T is designed with an easy-to-access fuel tank and a maintenance-free battery, reducing downtime and simplifying upkeep. Optional accessories are available, including mulching kits and towable carts, expanding the tractor's versatility for various gardening tasks.

Overall, the Husqvarna GTH2448T stands out as an excellent choice for those seeking a reliable, efficient, and user-friendly lawn tractor. Its powerful engine, adjustable cutting deck, and advanced features make it an essential tool for maintaining a beautiful and well-manicured lawn. Whether you are a seasoned gardener or a novice homeowner, the GTH2448T offers everything needed to tackle your landscaping tasks effectively.
Top Page Image Contents