Husqvarna GTH2448T To Replace Mower Blade Drive Belt See Fig, Mower Drive Belt Removal

Page 21

SERVICE AND ADJUSTMENTS

•Raise mower to highest position.

•Position any blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

•If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

02548

BB

FIG. 25

B

A

Tighten adjust nut

Loosen adjust nut

B to raise mower

B to lower mower

02950

Loosen jam nut A first

FIG. 26

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 27)

MOWER DRIVE BELT REMOVAL

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly.

•Remove screws (P) from mandrel covers (Q) and re- move covers.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

•Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

•Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown.

•Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Reassemble mandrel covers (Q). Securely tighten all screws.

•Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

 

P

Q

P

 

 

M

K

R

 

L

Q

 

R

 

 

S

 

R

FIG. 27

TO REPLACE MOTION DRIVE BELT (See Fig. 28)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness (A).

•Remove anti-rotation link (B) on right side of tractor.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 917.279260 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Stopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Operate Mower Reverse Operation System ROSBefore Starting the Engine Service REMINDER/HOUR MeterTo Operate on Hills To Transport See FigsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Before Each USE MaintenanceTractor BatteryBrake Operation TiresEngine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigsTo Remove Mower See Fig To Level Mower Turn nut right Turn nut left To raise mower To Replace Mower Blade Drive Belt See Fig Mower Drive Belt InstallationTo Replace Motion Drive Belt See Fig Mower Drive Belt RemovalBelt Installation To Start Engine with a Weak Battery See FigTo Check Brake Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Tractor Model no .279260 GTH2448T, Product no 43 SchematicElectrical KEY Part NO. NO. Description Chassis KEY Part Description Drive KEY Part NO. NO. Description Steering Assembly Engine Spark Arrester KITSeat Assembly Wheels and Tires DecalsMower Deck Tractor Model no .279260 GTH2448T, Product no 43 Mower Lift Tractor Model no .279260 GTH2448T, Product no 43 900 Key Part Description Briggs Engine Model Number 445677, Type Number 0476-E1 Tractor - Model NumberCarburetor Gasket SET 789A 1054 789B 1070 668 526 501 1005 474 877 332 1059 573 KEY Part Description Repair Parts Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

GTH2448T specifications

The Husqvarna GTH2448T is a remarkable lawn tractor designed for homeowners with medium to large-sized yards. Combining power, efficiency, and innovative features, the GTH2448T enhances your mowing experience while ensuring impressive performance.

At the heart of the GTH2448T is a robust 24 HP Kohler engine. This powerful engine provides ample torque and reliability, making it ideal for handling various terrains and mowing conditions. The automatic transmission allows for smooth driving and easy operation, enabling users to navigate around obstacles and tight spaces with confidence.

One of the standout features of the Husqvarna GTH2448T is its 48-inch cutting deck. This deck size strikes an excellent balance between maneuverability and mowing efficiency, allowing users to cover larger areas quickly while still being able to access narrow paths. The cutting height is adjustable, with options ranging from 1.5 inches to 4 inches, ensuring that you can customize your lawn's appearance according to your preferences.

The GTH2448T comes equipped with a tight turning radius, enhancing its agility and allowing for easier navigation in confined spaces. This feature is particularly valuable when mowing around flower beds, trees, and other landscape features. Additionally, the mower's ergonomic design ensures a comfortable riding experience, with a plush seat and user-friendly controls that are within easy reach.

The Husqvarna GTH2448T employs several innovative technologies, including the Air Induction Mowing Technology. This feature enhances airflow within the deck, promoting an even cut and reducing the chance of clumping, which results in a cleaner lawn appearance. Moreover, the tractor's durable construction and high-quality materials offer long-lasting performance, ensuring that your investment will stand the test of time.

For added convenience, the GTH2448T is designed with an easy-to-access fuel tank and a maintenance-free battery, reducing downtime and simplifying upkeep. Optional accessories are available, including mulching kits and towable carts, expanding the tractor's versatility for various gardening tasks.

Overall, the Husqvarna GTH2448T stands out as an excellent choice for those seeking a reliable, efficient, and user-friendly lawn tractor. Its powerful engine, adjustable cutting deck, and advanced features make it an essential tool for maintaining a beautiful and well-manicured lawn. Whether you are a seasoned gardener or a novice homeowner, the GTH2448T offers everything needed to tackle your landscaping tasks effectively.
Top Page Image Contents