Husqvarna GTH2454T owner manual Tractor, Brake Operation, Tires, Blade Care, Battery

Page 18

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See PSI on tires).

Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never operate unless the operator is in the seat.

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

 

02828

CHECK REVERSE OPERATION (ROS) SYSTEM

When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be sharp. Replace worn, bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 23)

Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

Remove blade bolt by turning counterclockwise.

Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

 

STAR

 

BLADE

CENTER

 

HOLE

 

 

 

BLADE BOLT

02544

MANDREL

(SPECIAL)

 

 

 

ASSEMBLY

FIG. 23

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

Remove terminal guard.

Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

Rinse the battery with plain water and dry.

Clean terminals and battery cable ends with wire brush until bright.

18

Image 18
Contents GTH2454T General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Mower Mower Front WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Unpack CartonInstall Mower and Drive Belt First Install ANTI-SWAY BAR S7/16 Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor StoppingTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig Reverse Operation System ROSTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips Maintenance Lubrication ChartBefore Each USE Brake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTractor See Fig Service and AdjustmentsTo Install Mower To Remove MowerTurn nut right Turn nut left To raise mower To Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Check Brake To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor Model NO. GTH2454T 96043002300, Product no 43Electrical KEY Part NO. NO. Description Chassis KEY Part Description Drive 211 532 19 62-12 Bushing Steering Assembly Spark Arrester KIT EngineSeat Assembly Decals Wheels and TiresMower Deck Tractor Model NO. GTH2454T 96043002300, Product no 43 Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

GTH2454T specifications

The Husqvarna GTH2454T is a robust and versatile lawn tractor designed specifically for homeowners who require efficient lawn care and maintenance. This model exemplifies Husqvarna's commitment to innovation and quality, making it a popular choice for residential landscapers and gardening enthusiasts alike.

One of the standout features of the GTH2454T is its powerful 24 HP Briggs & Stratton Intek V-Twin engine, which delivers ample power for a variety of mowing conditions. This dual-cylinder engine is designed to provide smooth operation and high torque, ensuring that users can tackle even the toughest mowing tasks with ease. The hydrostatic transmission offers seamless speed control, allowing for precise adjustments while navigating different terrains or executing sharp turns.

The cutting deck on the GTH2454T is 54 inches wide, offering an efficient mowing experience by reducing the number of passes needed to cover large areas. The deck is reinforced with a durable design that withstands the rigors of regular use, and it features an adjustable cutting height, enabling users to customize their mowing height to match their lawn’s specific needs. This flexibility contributes to healthier grass growth and overall aesthetic appeal.

Additionally, the GTH2454T incorporates advanced features such as a responsive steering system, which enhances maneuverability and allows for easy navigation around obstacles like trees and flower beds. The ergonomic seat design ensures comfort during extended periods of use, while the convenient controls are intuitively placed for easy access.

Another noteworthy aspect of the Husqvarna GTH2454T is its compatibility with various attachments, making it a multi-functional tool for yard maintenance. Users can equip it with accessories like baggers, snow plows, and carts to extend its usability throughout the year, transforming it into a reliable ally in different seasonal tasks.

With its combination of power, versatility, and comfort, the Husqvarna GTH2454T is not just a lawn mower but a comprehensive solution for maintaining beautiful outdoor spaces. It stands as a testament to Husqvarna’s expert engineering and dedication to providing tools that meet the evolving needs of modern homeowners. Whether it’s tackling thick grass, managing foliage, or preparing for winter snow, the GTH2454T is an investment that can enhance any lawn care routine.