Husqvarna GTH220 owner manual Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 20

SERVICE AND ADJUSTMENTS

CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

Depress clutch/brake pedal fully and set parking brake.

Place motion control lever in neutral (N) position.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key “OFF” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 20)

Place attachment clutch in “DISENGAGED” position.

Turn height adjustment knob to lowest setting.

Lower mower to its lowest position.

Remove retainer spring holding anti-swaybar to chas- sis bracket and disengage anti-swaybar from bracket.

Remove retainer springs from suspension arms at deck and disengage arms from deck.

Raise attachment lift to its highest position.

Remove two retainer springs from each front link and remove links.

Slide mower forward and remove belt from electric clutch pulley.

Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS.

TO INSTALL MOWER

Follow procedure described in “INSTALL MOWER AND DRIVE BELT” in the Assembly section of this manual.

ADJUSTMENT

 

 

NUTS

LIFT

FRONT

 

LINKS

SUSPENSION

SUSPENSION

 

BRACKET

ARMS

 

 

CHASSIS

 

FRONT MOWER

 

BRACKET

BRACKET

 

 

RETAINER

SPRING

ANTI-SWAY

BAR

RETAINER

SPRINGS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” on page 3 of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

Raise mower to its highest position.

Measure height from bottom of deck curl to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

Recheck measurements after adjusting.

BOTTOM

 

BOTTOM

OF CURL

 

OF CURL

A

GROUND LINE

A

FIG. 21

ELECTRIC

CLUTCH

PULLEY

FRONT

SUSPENSION

FRONTBRACKET

LINKS

RETAINER

SPRINGS

FRONT MOWER

BRACKET

FIG. 20

20

Image 20
Contents GTH220 Safety Rules Safe Operation Practices for Ride-On MowersModel Number GTH220 Serial Product SpecificationsCustomer Responsibilities Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Rolling Tractor OFF SkidInstall Seat See Fig To Attach Nose Roller See FigCheck Tire Pressure Check Brake SystemCheck for Proper Position of ALL Belts Install Mower and Drive Belt See FigsCheck Deck Levelness Checklist To Attach Front Bumper See FigLock Locked Reverse Neutral High LOW OperationUnlocked Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigsTo Operate on Hills To Transport See FigsIndicator Lights Before Starting the EngineCheck Engine OIL Level See Fig ADD GasolineMowing Tips Purge TransmissionLubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USEBattery TractorBrake Operation TiresEngine Transaxle CoolingTransaxle Pump Fluid BeltsCleaning Clean AIR INTAKE/COOLING AreasEngine OIL Filter MufflerService and Adjustments To Install MowerTo Level Mower Housing To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive BeltTo Adjust Attachment Clutch See Fig To Replace Mower Blade Drive Belt See FigTo Adjust Brake See Fig Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalTo Adjust Motion Control Lever See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN AdjustmentTo Start Engine with a Weak Battery See Fig Front Wheel CamberTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Attachment Lift Spring See Fig To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigsTo Adjust Carburetor See Fig Preliminary SettingFinal Setting Acceleration TestStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionOFF Service Notes Schematic Tractor Model NO. GTH220 954830167ARepair Parts ElectricalKEY Part NO. NO. Description 47120 Chassis and Enclosures KEY Part DescriptionGround Drive Repair Parts Steering Assembly 532124415 Wheel, Steering 532137094 Engine KEY Part NO. NO. Description Seat Assembly Decals Wheels & TiresGBD48 GSB42Lift Assembly Nut, Special Mower Deck KEY Part Description Transaxle Hydro Gear Model Number AYP Description Transaxle PUMP- Model Number BDU-10L-118 Service Notes Sighting Guide CUT This OUT Dotted Is a SlopeWarranty Statement Limited Warranty532150629 08.17.95 Kfsw