Husqvarna YTH24V42LS Unassembled Parts, Tools Required For Assembly, Slope Sheet Key

Page 5

UNASSEMBLED PARTS

UNASSEMBLED PARTS

Slope Sheet

Key

(1) Oil Drain Tube

(2) Keys

ASSEMBLY

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)	1/2" wrench	Tire pressure gauge
(2)	7/16" wrenches	Utility knife
		Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TOREMOVETRACTORFROMCARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

•Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

•For battery and battery cable installation see "RE- PLACING BATTERY" in the "Service and Adjustments" section in this manual.

LABEL

Fig. 1

TO ADJUST SEAT (See Fig. 2):

•Grasp adjustment handle(A) and pull up, slide seat to desired position and release adjustment handle.

A

Fig. 2

5

Image 5

Contents YTH24V42LS Owners Manual532 44 07002Safe Operation Practices for Ride-On Mowers SAFETY RULESI. GENERAL OPERATION II. SLOPE OPERATIONIII. CHILDREN V. SERVICEIV. TOWING GENERAL SERVICEPRODUCT SPECIFICATIONS TABLE OF CONTENTSCUSTOMER RESPONSIBILITIES SERVICE AND ADJUSTMENTSTOOLS REQUIRED FOR ASSEMBLY ASSEMBLYTO CHECK BATTERY See Fig TO ADJUST SEAT See FigCHECK DECK LEVELNESS CHECK TIRE PRESSURECHECK FOR PROPER POSITION OF ALL BELTS CHECK BRAKE SYSTEMOPERATION KNOW YOUR TRACTOR TO SET PARKING BRAKE See Fig HOW TO USE YOUR TRACTORSTOPPING See Fig TO USE THROTTLE CONTROL D See FigTO ADJUST GAUGE WHEELS See Fig TO ADJUST MOWER CUTTING HEIGHT See FigTO MOVE FORWARD AND BACKWARD See Fig K J LREVERSE OPERATION SYSTEM ROS TO STOP MOWER BLADESTO OPERATE ON HILLS TO TRANSPORT See Figs. 3 andBEFORE STARTING THE ENGINE SERVICE REMINDER/HOUR METERCHECK ENGINE OIL LEVEL ADD GASOLINEPURGE TRANSMISSION MOWING TIPSMAINTENANCE MAINTENANCEGENERAL RECOMMENDATIONS SCHEDULETRACTOR BATTERYBLADE CARE BLADE REMOVAL See FigCLEAN AIR SCREEN TRANSAXLE MAINTENANCEENGINE V-BELTSIN-LINE FUEL FILTER See Fig CLEANINGDECK WASHOUT PORT See Fig CAUTION Avoid all pinch points and movable parts See FigTO INSTALL MOWER See Figs SERVICE AND ADJUSTMENTSTO REMOVE MOWER See Fig A M C D C DF O P Q E H B TO LEVEL MOWER TO CHECK BRAKE TO REPLACE MOWER BLADE DRIVE BELTIDLER ARM BELT ROUTING ENGINE BLADE BELTTO REPLACE MOTION DRIVE BELT See Fig TO START ENGINE WITH A WEAK BATTERY See FigFRONT WHEEL TOE-IN/CAMBER TO REMOVE WHEEL FOR REPAIRS See FigTO REMOVE HOOD AND GRILL ASSEMBLY See Fig REPLACING BATTERY See FigREMOVAL/REPLACEMENT TO ADJUST THROTTLE CONTROL CABLEOTHER STORAGEFUEL SYSTEM ENGINE OILPROBLEM TROUBLESHOOTINGLoss of power CAUSEBattery will not to run when operfires” when turn Engine continuesTRACTOR - MODEL NO. YTH24V42LS 96043011500, PRODUCT NO. 960 43 SCHEMATICPTO SWITCH IGNITION SWITCHELECTRICAL TRACTOR - MODEL NO. YTH24V42LS 96043011500, PRODUCT NO. 960 43T15S With 12V Outlet OptionDESCRIPTION ELECTRICALPART chassis-texGT HUSQ II2r1 CHASSISCHASSIS drive-texK46pedal72r2 DRIVEDRIVE engine-texKawa-2cyl5 ENGINESPARK ARRESTER KIT ENGINE Steering-texLEGND237 STEERING ASSEMBLYAxle Asm., Front Seat SEAT ASSEMBLY532 42 WHEELS AND TIRES DECALSMOWER DECK MOWER DECK 532 40 34-07 Link Lift Susp Mower Rear MOWER LIFTONLY RIDE UP AND DOWN HILL NOT ACROSS HILL 15 DEGREES MAX SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATIONPrinted in the U.S.A 11.08.10 BAD