Husqvarna YTH2546 owner manual To Level Mower

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 22)

•With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

02948

 

FIG. 22

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 23)

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

FIG. 23

•If adjustment is necessary, see step in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 24 and 25) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position any blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

•If front tip of blade is not 1/8" to 1/2" lower than the rear

02548

BB

FIG. 24

tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

B

A

Tighten adjust nut

Loosen adjust

B to raise mower

nut B to lower

02950

mower

 

Loosen jam nut A first

FIG. 25

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents YTH2546 Twin Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigSystem Characteristics To Operate MowerService REMINDER/HOUR Meter Before Starting the EngineTo Operate on Hills Check Engine OIL LevelAutomatic Transmission Warm UP To Start Engine See FigPurge Transmission Mowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBrake Operation TiresEngine Cleaning IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Service and Adjustments To Level Mower Belt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Belt RemovalTo Remove Wheel for Repairs See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when KEY Part NO. no Description DecalsWheels and Tires Schematic 02929-194276Regulated-TexElectrical 102 104 101KEY Part Description Chassis KEY Part NO. no Description Drive 532 41 Spark Arrester KIT EngineSteering Assembly Mower Deck 532 41 Mower Housing Seat Assembly Mower Lift Service Notes Suggested Guide for Sighting Slopes for Safe Operation 532 41 06-05 Rev 05.10.07 AP

YTH2546 specifications

The Husqvarna YTH2546 is a versatile and powerful riding lawn mower designed for homeowners who seek reliability, performance, and ease of use in maintaining their lawns. With a robust 25 HP Kohler engine, this mower delivers exceptional power and efficiency, allowing users to tackle even the most challenging terrain with ease. The engine is engineered for smooth operation, ensuring a quiet ride while providing ample power for cutting grass at varying heights.

One of the standout features of the YTH2546 is its 46-inch cutting deck, which provides a wide cutting path, significantly reducing the time spent mowing larger lawns. The cutting deck is made from durable steel, enhancing its longevity and resistance to wear and tear. Additionally, the mower features a reinforced cutting deck with anti-scalp wheels, allowing for a clean cut and enhanced maneuverability while preventing damage to the lawn and the mower itself.

The YTH2546 incorporates a simple but effective cutting height adjustment system that allows users to quickly modify the cutting height to their preferred level, ranging from 1.5 to 4 inches. This flexibility enables homeowners to achieve the perfect grass height, promoting a healthy and well-maintained lawn. The mower also boasts a unique automatic blade engagement feature, which allows the operator to easily engage and disengage the blades using a simple lever, enhancing overall user convenience.

For added comfort, the Husqvarna YTH2546 is equipped with an ergonomic seat that is designed to provide ample cushioning during longer mowing sessions. The seat is adjustable to accommodate different operator sizes, ensuring a comfortable fit. Additionally, the controls are intuitively located, ensuring that users can easily navigate the mower without unnecessary distractions.

Another notable technology in the YTH2546 is its hydrostatic transmission. This system offers seamless speed control, allowing users to move forward or backward with the appropriate speed without the need for gear shifting. The result is improved control and reduced operator fatigue, making mowing more enjoyable.

In summary, the Husqvarna YTH2546 combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to maintain their lawns effortlessly. With its reliable engine, robust cutting deck, and innovative technologies, this riding lawn mower ensures a clean, precise cut while delivering unparalleled comfort and convenience.
Top Page Image Contents