Husqvarna YTH2546 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain

conditions.10

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG.9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflec- tor shield (S) in place.

S

FIG. 10

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en-

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH2546 Twin General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission To Start Engine See FigAutomatic Transmission Warm UP Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Cleaning IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Service and Adjustments To Level Mower To Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalFront Wheel TOE-IN/CAMBER To Check BrakeTo Remove Wheel for Repairs See Fig To Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove CABLES, Reverse OrderTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Wheels and Tires DecalsKEY Part NO. no Description Schematic 02929-194276Regulated-TexElectrical 102 104 101KEY Part Description Chassis KEY Part NO. no Description Drive 532 41 Spark Arrester KIT EngineSteering Assembly Mower Deck 532 41 Mower Housing Seat Assembly Mower Lift Service Notes Suggested Guide for Sighting Slopes for Safe Operation 532 41 06-05 Rev 05.10.07 AP

YTH2546 specifications

The Husqvarna YTH2546 is a versatile and powerful riding lawn mower designed for homeowners who seek reliability, performance, and ease of use in maintaining their lawns. With a robust 25 HP Kohler engine, this mower delivers exceptional power and efficiency, allowing users to tackle even the most challenging terrain with ease. The engine is engineered for smooth operation, ensuring a quiet ride while providing ample power for cutting grass at varying heights.

One of the standout features of the YTH2546 is its 46-inch cutting deck, which provides a wide cutting path, significantly reducing the time spent mowing larger lawns. The cutting deck is made from durable steel, enhancing its longevity and resistance to wear and tear. Additionally, the mower features a reinforced cutting deck with anti-scalp wheels, allowing for a clean cut and enhanced maneuverability while preventing damage to the lawn and the mower itself.

The YTH2546 incorporates a simple but effective cutting height adjustment system that allows users to quickly modify the cutting height to their preferred level, ranging from 1.5 to 4 inches. This flexibility enables homeowners to achieve the perfect grass height, promoting a healthy and well-maintained lawn. The mower also boasts a unique automatic blade engagement feature, which allows the operator to easily engage and disengage the blades using a simple lever, enhancing overall user convenience.

For added comfort, the Husqvarna YTH2546 is equipped with an ergonomic seat that is designed to provide ample cushioning during longer mowing sessions. The seat is adjustable to accommodate different operator sizes, ensuring a comfortable fit. Additionally, the controls are intuitively located, ensuring that users can easily navigate the mower without unnecessary distractions.

Another notable technology in the YTH2546 is its hydrostatic transmission. This system offers seamless speed control, allowing users to move forward or backward with the appropriate speed without the need for gear shifting. The result is improved control and reduced operator fatigue, making mowing more enjoyable.

In summary, the Husqvarna YTH2546 combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to maintain their lawns effortlessly. With its reliable engine, robust cutting deck, and innovative technologies, this riding lawn mower ensures a clean, precise cut while delivering unparalleled comfort and convenience.
Top Page Image Contents