Husqvarna YTH24V54 owner manual Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 21

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 32)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove mower belt from electric clutch pulley (M).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Gotoeithersideofmoweranddisconnectmowersuspen- sion arm (A) from chassis and rear lift link (C) from rear mowerbracket(D)-removeretainerspringsandwashers.

•Go to other side of mower and disconnect the suspen- sion arm and rear lift link.

CAUTION: After rear lift links are discon- nected, the attachment lift lever will be spring loaded. Have a tight grip on lift lever when changing position of the lever.

•From right side of mower, disconnect anti-sway bar (S) from right rear mower bracket (D) - remove retainer spring and washer and pull mower toward you until the bar falls from the hole in bracket.

•Turn tractor steering wheel to the left as far as it will go.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Follow procedure described in “INSTALL MOWER AND DRIVE BELT” in the Assembly section of this manual.

 

L

 

 

B

 

 

 

 

 

M

F

 

 

 

 

 

 

 

 

 

 

E

K

 

 

 

A

 

 

 

 

 

H

 

 

 

 

 

C

D

S

 

 

 

 

C

D

 

 

 

 

 

 

Fig. 32

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 33)

MOWER DRIVE BELT REMOVAL

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly.

•Remove screws (P) from mandrel covers (Q) and remove covers.

•Removeanydirtorgrassclippingswhichmayhaveaccu- mulated around mandrels and entire upper deck surface.

•Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (V).

MOWER DRIVE BELT INSTALLATION

•Install belt around all mandrel pulleys (R) and around idler pulleys (V) as shown.

•Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Reassemble mandrel covers (Q). Securely tighten all screws.

•Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

P

P

 

 

 

L

M

P

 

Q

 

K

R

Q

R

V

 

 

R

 

Fig. 33

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 917.289640 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Mower Mower Front Wheel Unassembled PartsSlope Sheet KeysTools Required for Assembly AssemblyToremovetractorfromcarton Before Removing Tractor from SkidInstall ANTI-SWAY BAR S if Equipped See Turn Steering Wheel Left and Position Mower See FigANTI-SWAY BAR S Attach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigAttach Front Link E See Fig Check Tire Pressure Install Belt on Engine Clutch Pulley M SeeCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Reverse Operation System ROS on Position Know Your TractorTo SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To USE Cruise Control J See FigTo Stop Mower Blades Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsBefore Starting the Engine Service REMINDER/HOUR MeterCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsMaintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBrake Operation TiresEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See FigTo Level Mower To Check Brake Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel See FigReplacing Battery See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTransmission Other StorageFuel System Engine OILProblem Cause Correction Battery will not To run when operFires when turn Engine continuesTractor Model NO. YTH24V54 SchematicElectrical KEY Part Description ElectricalChassis Tractor Model NO. YTH24V54 197 DriveKEY Part NO. NO. Description Engine 30!2+ª!22%34%2ª+4Engine Power Rating Information Steering Assembly KEY Part NO. NO. Description Mower Deck 532 40 31-25 Deck Weldment Mower Mower Lift Seat Assembly Wheels and Tires DecalsLiquid Gasket and the Breather Gasket are Interchangeable Briggs Engine Model 445677, Type Number 1198-B1Tractor Model NO. YTH24V54 967 628 385 601A 918 240 334 788 387 526 474 693997 Tractor Model NO. YTH24V54 Tufftorq Transaxle Model Number K46BT Tractor - Model Number YTH24V54Tractor - Model Number YTH24V54 Service Notes Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWarranty Statement
Top Page Image Contents