Husqvarna YTH2242 To Adjust Gauge Wheels See Fig, To Operate on Hills, To Transport See Figs, Mph

Page 12
GAUGE
WHEEL MOUNTING BRACKET
3/8-16
LOCKNUT 3/8 WASHER

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

GAUGE WHEEL

SHOULDER BOLT

• Raise attachment lift to highest position with attachment

 

lift control.

•

Pull freewheel control out and down into the slot and

 

release so it is held in the disengaged position.

•

Do not push or tow tractor at more than two (2)

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

MPH.

• To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

FIG. 9

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

"ENGAGED"

POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

LOW

POSITION

DEFLECTOR SHIELD

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

FIG. 8

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents YTH2242 Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering WheelKey Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig Install Mulcher Plate See If previously removedTo Convert to Bagging or Discharging Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate on HillsTo Transport See Figs To Operate Mower See FigBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsMaintenance Lubrication ChartService Dates General RecommendationsTractor Engine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Check and Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Remove Hood and Grill Assembly See Fig To Replace Headlight BulbInterlocks and Relays To Replace FuseTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigsTo Adjust Carburetor Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor Model NO. YTH2242 YTH2242A, Product no 57Electrical KEY Part Description Chassis and Enclosures 532 17 46-19 Chassis Stamping Drive Repair Parts Steering Assembly 532 16 Wheel Steering Seat Assembly 532 18 SeatDecals Wheels & TiresEngine Mower Lift Mower Deck 532 17 85-15 Washer, Hardened Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 18 54-46 Rev 1.3.03 RD
Related manuals
Manual 45 pages 9.06 Kb

YTH2242 specifications

The Husqvarna YTH2242 is a versatile and robust garden tractor designed for homeowners seeking a reliable and efficient mowing solution. This model features a powerful 22 horsepower Kohler engine that provides ample power for cutting through tough grass and uneven terrain. The engine is engineered for durability and performance, ensuring that it can handle a variety of yard conditions with ease while delivering smooth starts and strong acceleration.

One of the standout features of the YTH2242 is its 42-inch cutting deck, which allows for a wider cutting path, making it ideal for mid-sized lawns. The cutting height can be easily adjusted with a lever located on the dashboard, offering six different height positions to achieve the perfect grass length. This feature is particularly beneficial for homeowners who prefer maintaining a manicured lawn or adjusting cut height for seasonal changes.

The YTH2242 is equipped with a hydrostatic transmission, allowing for smooth, variable speed control without the need for manual gear shifting. This transmission technology enables effortless navigation around obstacles and provides increased maneuverability, especially in tight spaces. Additionally, the model has tight turning capabilities, making it effective for trimming around trees and flower beds.

Ergonomy is a key consideration in the design of the YTH2242. The comfortable seat is adjustable, allowing drivers of different sizes to find their ideal driving position effortlessly. The user-friendly dashboard is equipped with easy-to-read gauges and controls, enhancing the overall experience. The steering wheel is designed for precise control, minimizing fatigue during longer mowing sessions.

For added convenience, the YTH2242 features a connector for optional attachments, such as bags, mulchers, and snow removal equipment, promoting year-round usability. The tight-knit construction and quality materials ensure longevity, and the cutting deck’s washout port simplifies maintenance by allowing users to clean the underside easily, preventing grass buildup.

In summary, the Husqvarna YTH2242 combines power, flexibility, and comfort in a compact design, making it a valuable addition to any homeowner's gardening arsenal. With its reliable engine, adjustable cutting deck, user-friendly features, and adaptability, it stands out as a top choice for those looking to maintain a pristine lawn with ease.
Top Page Image Contents