Husqvarna YTH2242 Install Seat See Fig, Install Mulcher Plate See If previously removed

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

Lower seat into operating position and sit on seat.

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

Get off seat without moving its adjusted position.

Raise seat and tighten adjustment knob securely.

SEAT SHOULDER

BOLT

SEAT PAN

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

Press lift lever plunger and raise attachment lift lever to its highest position.

Release parking brake by depressing clutch/brake pedal.

Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

Roll tractor forward off skid.

Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

Be sure all the above assembly steps have been com- pleted.

Check engine oil level and fill fuel tank with gasoline.

Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

Place motion control lever in neutral (N) position.

Press lift lever plunger and raise attachment lift lever to its highest position.

Start the engine.After engine has started, move throttle control to idle position.

Release parking brake.

Slowly move the motion control lever forward and slowly drive tractor off skid.

Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

Turn ignition key to "STOP" position.

Continue with the instructions that follow.

INSTALL MULCHER PLATE (See Fig. 4) (If previously removed)

Raise and hold deflector shield in upright position.

Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

Hook front latch into hole on front of mower deck.

Hook rear latch into hole on back of mower deck.

CAUTION: Do not remove deflector shield from mower.

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessary to change blades. The mulcher blades are designed for discharging and bagging also.

DEFLECTOR

MULCHER

SHIELD

PLATE

 

LATCH

HOOKS

7

FIG. 4

Image 7
Contents YTH2242 II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel KeyBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Mulcher Plate See If previously removed Install Seat See FigTo Convert to Bagging or Discharging Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsGeneral Recommendations MaintenanceLubrication Chart Service DatesTractor Engine Spark Plugs CleaningEngine OIL Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral ADJUSTMENTSee FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs See Fig To Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Attach Jumper CablesTo Replace Fuse To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Choke Control See Figs To Adjust Throttle Control Cable See FigTo Adjust Carburetor Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor Model NO. YTH2242 YTH2242A, Product no 57 SchematicElectrical KEY Part Description Chassis and Enclosures 532 17 46-19 Chassis Stamping Drive Repair Parts Steering Assembly 532 16 Wheel Steering 532 18 Seat Seat AssemblyWheels & Tires DecalsEngine Mower Lift Mower Deck 532 17 85-15 Washer, Hardened Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWarranty Statement 532 18 54-46 Rev 1.3.03 RD
Related manuals
Manual 45 pages 9.06 Kb

YTH2242 specifications

The Husqvarna YTH2242 is a versatile and robust garden tractor designed for homeowners seeking a reliable and efficient mowing solution. This model features a powerful 22 horsepower Kohler engine that provides ample power for cutting through tough grass and uneven terrain. The engine is engineered for durability and performance, ensuring that it can handle a variety of yard conditions with ease while delivering smooth starts and strong acceleration.

One of the standout features of the YTH2242 is its 42-inch cutting deck, which allows for a wider cutting path, making it ideal for mid-sized lawns. The cutting height can be easily adjusted with a lever located on the dashboard, offering six different height positions to achieve the perfect grass length. This feature is particularly beneficial for homeowners who prefer maintaining a manicured lawn or adjusting cut height for seasonal changes.

The YTH2242 is equipped with a hydrostatic transmission, allowing for smooth, variable speed control without the need for manual gear shifting. This transmission technology enables effortless navigation around obstacles and provides increased maneuverability, especially in tight spaces. Additionally, the model has tight turning capabilities, making it effective for trimming around trees and flower beds.

Ergonomy is a key consideration in the design of the YTH2242. The comfortable seat is adjustable, allowing drivers of different sizes to find their ideal driving position effortlessly. The user-friendly dashboard is equipped with easy-to-read gauges and controls, enhancing the overall experience. The steering wheel is designed for precise control, minimizing fatigue during longer mowing sessions.

For added convenience, the YTH2242 features a connector for optional attachments, such as bags, mulchers, and snow removal equipment, promoting year-round usability. The tight-knit construction and quality materials ensure longevity, and the cutting deck’s washout port simplifies maintenance by allowing users to clean the underside easily, preventing grass buildup.

In summary, the Husqvarna YTH2242 combines power, flexibility, and comfort in a compact design, making it a valuable addition to any homeowner's gardening arsenal. With its reliable engine, adjustable cutting deck, user-friendly features, and adaptability, it stands out as a top choice for those looking to maintain a pristine lawn with ease.