Husqvarna YTH2242 owner manual Tractor

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 12)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer se- curing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

16

TRAILING

 

EDGE UP

BLADE

 

CENTER

FLAT WASHER

HOLE

MANDREL

 

ASSEMBLY

LOCK WASHER

STAR

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

CENTER HOLE

5/8" BOLT

 

OR PIN

BLADE

FIG. 13

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents YTH2242 Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering WheelKey Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Mulcher Plate See If previously removed Install Seat See FigTo Convert to Bagging or Discharging Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate on HillsTo Transport See Figs To Operate Mower See FigBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsMaintenance Lubrication ChartService Dates General RecommendationsTractor Engine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Check and Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Remove Hood and Grill Assembly See Fig To Replace Headlight BulbInterlocks and Relays To Replace FuseTo Adjust Choke Control See Figs To Adjust Throttle Control Cable See FigTo Adjust Carburetor Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor Model NO. YTH2242 YTH2242A, Product no 57Electrical KEY Part Description Chassis and Enclosures 532 17 46-19 Chassis Stamping Drive Repair Parts Steering Assembly 532 16 Wheel Steering Seat Assembly 532 18 SeatDecals Wheels & TiresEngine Mower Lift Mower Deck 532 17 85-15 Washer, Hardened Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 18 54-46 Rev 1.3.03 RD
Related manuals
Manual 45 pages 9.06 Kb

YTH2242 specifications

The Husqvarna YTH2242 is a versatile and robust garden tractor designed for homeowners seeking a reliable and efficient mowing solution. This model features a powerful 22 horsepower Kohler engine that provides ample power for cutting through tough grass and uneven terrain. The engine is engineered for durability and performance, ensuring that it can handle a variety of yard conditions with ease while delivering smooth starts and strong acceleration.

One of the standout features of the YTH2242 is its 42-inch cutting deck, which allows for a wider cutting path, making it ideal for mid-sized lawns. The cutting height can be easily adjusted with a lever located on the dashboard, offering six different height positions to achieve the perfect grass length. This feature is particularly beneficial for homeowners who prefer maintaining a manicured lawn or adjusting cut height for seasonal changes.

The YTH2242 is equipped with a hydrostatic transmission, allowing for smooth, variable speed control without the need for manual gear shifting. This transmission technology enables effortless navigation around obstacles and provides increased maneuverability, especially in tight spaces. Additionally, the model has tight turning capabilities, making it effective for trimming around trees and flower beds.

Ergonomy is a key consideration in the design of the YTH2242. The comfortable seat is adjustable, allowing drivers of different sizes to find their ideal driving position effortlessly. The user-friendly dashboard is equipped with easy-to-read gauges and controls, enhancing the overall experience. The steering wheel is designed for precise control, minimizing fatigue during longer mowing sessions.

For added convenience, the YTH2242 features a connector for optional attachments, such as bags, mulchers, and snow removal equipment, promoting year-round usability. The tight-knit construction and quality materials ensure longevity, and the cutting deck’s washout port simplifies maintenance by allowing users to clean the underside easily, preventing grass buildup.

In summary, the Husqvarna YTH2242 combines power, flexibility, and comfort in a compact design, making it a valuable addition to any homeowner's gardening arsenal. With its reliable engine, adjustable cutting deck, user-friendly features, and adaptability, it stands out as a top choice for those looking to maintain a pristine lawn with ease.
Top Page Image Contents