1. Networked standby mode
1.1Test result where all NTW wired ports are connected and all NTW wireless ports activated ( This value could exceed requirement limit )
| Test date |
| 4th Jan. 2016 |
| Power Consumption (W) |
| 5.3 |
|
|
| (rounded to the 1st decimal place) |
| |||
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
1.2 The number and type of network ports ( it shall be declared if the same physical network port accommodates two or more types of network ports )
Logical Ports: 1 x Ethernet (100BaseT) (Position : Rear side of equipment)
Physical Ports: 1 x Ethernet
1.3Test result and information for each type of network port:
(a)The ( maximum ) power consumption
(b)The default time after which the power management function, or a similar function, switches the equipment into a condition providing networked standby
(c)The trigger that is used to reactivate the equipment
(d)The ( maximum ) performance specifications
(e)The communication protocol used by the equipment
| NTW Port | (a), W | (b), min |
| (c) |
| (d) |
| (e) | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Ethernet |
| 1.6 | N/A | IP traffic / ICMP ping |
| 100 Mbps | Ethernet protocol | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- |
| - | - |
| - |
| - |
|
|
| - | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- |
| - | - |
| - |
| - |
|
|
| - | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- |
| - | - |
| - |
| - |
|
|
| - | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- |
| - | - |
| - |
| - |
|
|
| - | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1.3 Test parameters |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| parameters |
|
| Actual | Limit |
| parameters |
|
|
| Actual | Limit | |
|
|
|
|
|
|
|
|
|
|
| |||
| Ambient temperature ( ) | 26.0 | 23±5 |
| Test voltage (V) |
|
|
| 230 | 230±2.3 | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Test frequency (Hz) | ℃ | 50 | 50±0.5 |
| Total harmonic | distortion |
|
| 1.42 | 2 | ||
|
|
|
|
| |||||||||
|
|
|
|
|
|
| (%) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Crest factor |
|
| 1.40 | 1.34~1.49 | - |
|
|
| - | - | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1.5 Whether all network ports are deactivated before delivery
Not all network ports are deactivated before delivery
1.6 Whether the equipment qualifies as HiNA equipment or equipment with HiNA functionality ( where no information is provided, this is considered not to be the case )
N/A
1.7 Instrumentation
Test instruments which were used in the test are as follows;