Asus P2B manuals
Computer Equipment > Mouse
When we buy new device such as Asus P2B we often through away most of the documentation but the warranty.
Very often issues with Asus P2B begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Mouse Asus P2B is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Mouse on our side using links below.
64 pages 0 b
2 USER'S NOTICEProduct Name: ASUS P2B Manual Revision: 1.03 E302 Release Date: November ASUS P2B User’s Manual 3 ASUSTeK COMPUTER INCMarketing Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH 4 CONTENTS6 FCC & DOC COMPLIANCEFederal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help Canadian Department of Communications Statement 7 How this Manual is OrganizedItem Checklist 8 Features of the ASUS P2B Motherboard10 Layout of the ASUS P2B Motherboard11 JumpersExpansion Slots/Sockets Hardware Monitor Connectors Board Layout 12 Installation Steps1. Jumpers 14 III.INSTALLATION3.CPU Bus Frequency (FS0, FS1, FS2) 4.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Internal External CPU Bus Frequency Set the jumpers by the Internal speed of your processor as follows: 17 2.System Memory (DIMM)19 3.Central Processing Unit (CPU)24 4.Expansion Cards26 5. External Connectors33 Power Connection Procedures34 Flash Memory Writer Utility37 6. BIOS SetupLoad Defaults 38 Standard CMOS SetupDetails of Standard CMOS Setup: 39 TimeHard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option Standard CMOS 40 Auto detection of hard disks on bootupAuto NOTE: SETUP Defaults are noted in parenthesis next to each function heading Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) EGA/VGA CGA Mono If you are using a VGA or any higher resolution card, choose EGA/VGA Halt On (All Errors) 41 BIOS Features SetupDetails of BIOS Features Setup 42 BIOSBIOS CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache BIOS Update (Enabled) Quick Power On Self Test (Enabled) HDD Sequence SCSI/IDE First (IDE) IDE SCSI Boot Sequence (A,C) A,C A,CDROM,C CDROM,C,A D,A E,A F,A C only LS/ZIP, C C,A A, C Boot Up Floppy Seek (Disabled) When enabled, the BIOS will seek drive A once Floppy Disk Access Control (R/W) IDE HDD Block Mode Sectors (HDD MAX) 43 Security Option (System)Supervisor Password User Password System Setup PS/2 Mouse Function Control (Auto) PCI/VGA Palette Snoop (Disabled) OS/2 Onboard Memory > 64M (Disabled) Video ROM BIOS Shadow (Enabled) C8000-CBFFFto DC000-DFFFF(Disabled) Boot Up NumLock Status (On) This field enables users to activate the Number Lock function upon system boot Typematic Rate Setting (Disabled) Typematic Rate (Chars/Sec) (6) Typematic Delay (Msec) (250) 44 Chipset Features SetupDetails of Chipset Features Setup 45 Graphics Aperture Size (64MB)Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Memory Hole At 15M–16M(Disabled) DRAM are xx bits wide If your DRAM modules do not have ECC chips (e.g. 8 chips), they are considered 64 bits and the following will be displayed instead: Data Integrity Mode (Non-ECC) Onboard FDC Controller (Enabled) Chipset Features 46 Onboard FDC Swap A & B (No Swap)Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Onboard Serial Port 2 (2F8H/IRQ3) Onboard Parallel Port (378H/IRQ7) Parallel Port Mode (ECP+EPP) ECP DMA Select (3) ECP ECP+EPP Parallel Port Mode UART2 Use Infrared (Disabled) Onboard PCI IDE Enable (Both) primary secondary both disable IDE Ultra DMA Mode (Auto) 0, 1, 2, 3 ), it is necessary for these to be independent. The default setting of will allow autodetection to ensure optimal performance 47 Power Management SetupDetails of Power Management Setup 48 Video Off Method (DPMS OFF)DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby DPMS Suspend V/H SYNC+Blank PM Timers HDD Power Down (Disable) 1–15 Min Suspend Mode (Disable) 30 sec 1 Min 2 Min 4 Min 8 Min 20 Min 30 Min 40 Min 1 Hour Disable Power Up Control PWR Button < 4 Secs (Soft Off) Soft Off Suspend No Function 49 PWR Up On Modem Act (Enabled)AC PWR Loss Restart (Disabled) Disabled Wake On LAN (Enabled) Automatic Power Up (Disabled) Fan Monitor (xxxxRPM) Thermal Monitor (xxxC/xxxF) Voltage Monitor (xx.xV) 50 PNP and PCI Setup52 Load BIOS DefaultsLoad Setup Defaults 53 Supervisor Password and User Password54 IDE HDD Auto Detection55 Save & Exit SetupExit Without Saving 56 Desktop Management Interface (DMI)59 ASUS PCI-L101Fast Ethernet Card60 FeaturesSoftware Driver Support Question and Answer
Also you can find more Asus manuals or manuals for other Computer Equipment.